20 Most Recent Canon PIXMA MP600 all-In-One InkJet Printer - Page 2 Questions & Answers

Your printer may not have the ability to recognize the files you have in the stick. Did you ever think of that?

You have to make sure the ip address is correct on modem and computer port If you need further help, I’m available over the phone at https://www.6ya.com/expert/alex_22751bbefa74c3d0

Try a hard reset followed by uninstalling and reinstalling the printer software

Hi. Probably the problem is the print head .

No you can not.

Description

Reseat the Print Head to resolve the U051 / U052 error.

Solution

Errors displayed on the printer's LCD screen:

• U051 Print head is not installed. Install the print head.
• U052 The type of print head is incorrect. Install the correct print head.

Reseat the Print Head:

1. Make sure that the power is turned on, and open the Paper Output Tray gently
2. Lift the Scanning Unit (Cover), then hold it open with the Scanning Unit Support (A). (The print head will move to the replacement position.)
3. Remove all the Ink Tanks in the following manner.
   1. Push the tab (B) and lift the ink tank to remove.
   2. Do not touch the Print Head Lock Lever (C) while removing the ink tanks.
4. Once the ink tanks have been removed, raise the print head lock lever.
5. Tilt the print head slightly towards the front of the machine and lift out gently. Caution: Do not touch the print head nozzles <1> , electrical contacts <2>, or ink supply ports <3>. Doing so may cause printing problems. *Before proceeding to next step, check the carriage area for packing material, torn paper, etc. and remove if found
6. Tilt the Print Head and set it in place. Lower the Print Head Lock Lever (E) completely.
7. Insert ink tanks into the print head.
   1. Insert the front end of ink tank into the Print Head at a slant. Make sure that the position of the ink tank matches the label.
   2. Press the mark (Push) on the ink tank until the ink tank snaps firmly into place. Make sure that the ink lamp lights up red.
8. Lift the Scanning Unit (Cover) slightly to set the Scanning Unit Support back to its original position, and gently close the Scanning Unit (Cover). Caution: When closing the scanning unit (printer cover), be careful not to jam fingers. Note: When the next printing begins, the print head cleaning will begin automatically.

If you have reseated the ink tanks and print head and the error still appears, our industry-leading support team is available to help you Monday through Friday from 10 AM to 10PM EST. You can contact our technical support experts by phone or email: Call 1-800-OK-CANON (1-800-652-2666)

Hi! As a first course of action, please unplug the printer from power source and long press the power button for like 10secs. Plug the printer from power source then press the power button and see what happens. If no luck, you may need to update the printer's firmware by downloading from the web. Just type your printer model and add firmware. Hope this helps and have a good one!

reset canon MP280 error

The simplest thing would be to try unplugging the printer from the power source. Let it rest for 5 - 10 minutes then plug back in to the power supply and see if that resolves the problem.

If not you are going to need to do a thorugh inspection to verify that all paper remnants have been removed.

The following is for the MP600:

Issue: ERROR LCD: The paper is jammed. Clear the paper and press [OK].
Solution: Removing paper jams MP600


Removing Obstructions or Jammed Paper If [Paper output slot - The paper is jammed. Clear the paper and press OK] appears on the LCD, follow this procedure to clear the paper jam Clearing paper jams from the auto sheet feeder (ASF) or paper output slot
Clearing paper jams inside the printer
Clearing credit card-sized or 4" x 6" paper jammed inside the printer

ASF / Paper Output Slot

1. Turn off the printer.
   
   
2. Remove paper from the ASF.
   
   
3. Gently pull the jammed paper out.
   
4. 1. If paper is visible from the ASF, use both hands to pull the paper out slowly.
      
   2. If paper is visible from the paper output slot, use both hands to pull the paper out slowly.
      
      
      The above illustration shows a PIXMA MP500.
      
      
5. If the paper tears and a piece of that remains inside the printer, open the scanning unit (printer cover) and remove the paper from inside the printer.
   
   Note:
   Be careful not to touch the components inside the printer.
   
   
   
6. Turn on the printer and confirm that the Alarm light is off.
   (If the jammed paper remains in the printer, the paper may be automatically ejected.)
   
   
7. Load paper back into the ASF.
   
   
8. Press to clear the message and continue printing. If you are printing from an application software, follow the instructions displayed on your computer.
   

Top
Paper jams inside the printer

1. Turn off the printer and disconnect the power cord and USB cable.
   
   
2. Remove the jammed paper slowly using the following procedure.
   
3. 1. Open the rear cover to check if the paper is jammed.
      
      
      
   2. Pull out the cassette and check if the paper is jammed inside the cassette area.
      
      
      
   3. Stand the printer with the left side down, holding the document cover.
      
   4. Press the tabs together and pull the green cover toward you.
      
   5. Check if the paper is jammed.
      (If you were not doing Duplex printing, you do not have to follow this procedure.)
      
      
      
      
   6. Close the green cover and place the printer back to a normal position.
      
4. Reconnect the power cord and power on the printer. Confirm the Alarm light is off.
   
   
5. Load paper back into the ASF or cassette.
   
   
6. Press to clear the message and continue printing. If you are printing from an application software, follow the instructions displayed on your computer.
   

Top

Clearing credit card-sized paper jammed inside the printer
Credit card-sized and 4" x 6" sized paper must be loaded properly. If this media is not loaded properly, it will feed into the printer and will not exit. Credit card-sized paper should only be loaded in the ASF and in portrait orientation. 4" x 6" sized paper can be loaded in the ASF or cassette. But must be loaded portrait orientation.
If credit card-sized paper was loaded in landscape orientation in the ASF and did not eject (exit), please follow this procedure.

1. Turn off the printer.
   
   
2. Load the same paper type that is jammed inside the printer in portrait orientation.
   
   
   
   
3. Power on the printer.
   The paper stock in the ASF will automatically feed the jammed paper from the printer.
   
   
4. To resume printing, load the paper in portrait orientation.

If 4" x 6" sized paper was loaded in landscape orientation in the cassette and did not eject (exit), please follow this procedure.

1. Turn off the printer.
   
   
2. Open the rear cover.
   
   
3. Fold in four a piece of letter-sized plain paper.
   
   
4. Push in the folded paper until it hits the jammed paper.
   
   
   
   
5. If the jammed paper is visible from inside the printer area, pull it out and proceed to step 7.
   
   
6. If the jammed paper cannot be pulled out, push in the folder paper from the rear so the jammed paper is in between the feed rollers.
   
   
7. Pull out the folded paper and close the rear cover.
   
   
8. Power on the printer and confirm that the Alarm light is off.
   The jammed paper should automatically eject.
   
   
9. To resume printing, load the paper in portrait orientation.

Trust this is helpful.

Try this link http://www.usa.canon.com/consumer/controller?act=ModelInfoAct&fcategoryid=116&modelid=13800#SupportDetailAct
has step by step info on how to change the language on the printer
Thanks
Ranjit [email protected]

The scanner unit cannot detect the home position, or the scanner unit warming-up is not performed properly at power-on. You can not reset the error. Flat cable or scanner unit is defective, if you are lucky it is just stucked.

Added a pic with part of manual, follow the instructions, and language will become english again!

Error Code 6502 appears generally after chaging a cartridge.

Solution:

1. Unplug the printer.
2. Remove the faulty Cartridge
3. Plug in the printer and press and hold power button
4. Keep it held down. Press Resume twice, and this should reset the fault.

All Best: Pineworks

Error code [6000] or light blinking 3 times.
1. Smearing or scratches on the LF encoder. Please clean the LF encoder.
2. Foreign material or paper debris in the LF drive. Please remove any foreign materials if encounter.
3. Check cable connection.
4. Replace LF encoder or Logic Board

It seems that your printer cartridge is not proper for for MP600 or cartridge is not properly installed or it's installed to wrong position. Check manual the right positions for each cartridge and right codes for each cartridge. You can load manuals here http://www.usa.canon.com/cusa/support/consumer/printers_multifunction/pixma_mp_series/pixma_mp600#BrochuresAndManuals

it means your computer does not recognise the printer you need to change the formatter board for your printer

Hi There,

1
Check the device connected to the Direct Print Port. Printing photos directly is possible with a PictBridge compliant device or the optional Bluetooth Unit BU-30.

2
A communication time out occurs if an operation takes too long or if it takes too much time to send data. This may cancel printing. In such cases, disconnect and reconnect the USB cable. When printing from a PictBridge compliant device, depending on the model or brand of your device, you may have to select a PictBridge compliant print mode on the device before connecting it to the machine. You may also have to turn on your device or select Play mode manually after connecting the device to the machine. Perform necessary operations before connecting your device referring to its instruction manual. If the error is still not resolved, check if you can print another photograph.