20 Most Recent Polaroid TLA-01511C 15 in. LCD Television - Page 5 Questions & Answers

I would recommend using the S-video connection for the DVD to the TLA-01511C TV's S-video. Then, press the input button and go down to the S-video option and you should be good to go - it worked for me. Hope this helps you!

ya got to pul the panel apart to remove the old connection then you have to solder a new one in place mabey Radio shack might have a generic part to fix it . just trying

look in the functions on the remote theres a tool section or set up guide that will come up look in owners manual

did you pre program the chanels into the tv i had the same problem make sure your pointing the controller at the tv its a little **** at times

i'll look for mine i think i have the same flat screen . I no its a polaroid and its 15" screen witha built in dvd player . post again for camone311

please provide brand name and model no.

thanks

I see this is an old message so you have probably tossed or retired this set.
The problem is likely in the power supply section of the set.
If it is elsewhere in the set, the power supply may be cycling to avoid further damage or even a fire.
I suggest you not leave this set plugged in anywhere it cannot be seen.

I believe there is an auto-center option in the computer part of the menu. If this does not work there is also a position option like CRT's have, that will allow you to manually change the position of the picture. If all else fails try changing your resolution to 1280 x 800, then auto-centering.

1) Use 2 new AA batteries in RC32 remote control;
2) Slide mode switch to "TV";
3) Press and hold the MUTE and SELECT keys at the same
time until the green light under the selected switch
position flashes twice, then release both keys.
4) Enter 9-9-1-1.
5) Press PWR button on TV.
6) Point the remote at the TV and press CHAN+. Repeatedly press CHAN+ until the TV turns off. Every time CHAN+ is pressed the remote advances to the next code and power is transmitted to the component.
7) Use the CHAN- key to step back a code.
8) When the TV turns off, stop pressing the CHAN+ key. Then, press and release the SELECT key. If the light flashes 3 times before the TV or component responds, you've cycled through all codes and the code you need is not available. You must use the TV remote control.
9) To verify the code, slide the MODE switch to the appropriate position.
10) Press and hold the MUTE and SELECT keys at the same time until the green light under the selected switch position flashes twice, then release both keys.
11) Enter 9-9-0. (The green light under the selected
switch position flashes twice.)
12) To view the first digit in the code, Press and release then number 1 key. Wait three seconds, and count the number of times the green light flashes. Write this number down in the TV owner manual.
13) Press number 2 for the second digit, 3 for the third digit, 4 for the fourth digit and 5 for the final digit.

To control TV volume from Directv RC32:
1. Press and hold the MUTE and SELECT keys until the
green light under the DIRECTV position flashes twice,
then release both keys.
2. Using the number keys, enter 9-9-3. (The green light
will flash twice after the 3.)
3. Press and release the VOL+ key. (The green light
flashes 4 times.)

If your Polaroid Roku TV is working fine but the red light is continuously flashing, it could indicate an issue that may need attention. Here are some steps you can try to troubleshoot the problem:

1. Power Cycle:
   • Turn off the TV and unplug it from the power source.
   • Wait for at least 5 minutes.
   • Plug the TV back in and turn it on.
2. Check Remote Control:
   • Ensure that there are no stuck buttons on the remote control. Press each button to make sure they are not stuck in the pressed position.
3. Update Firmware:
   • Check if there is a firmware update available for your TV. You can usually find this information in the TV's settings menu.
4. Reset to Factory Settings:
   • Perform a factory reset on your TV. This will erase your settings, so be sure to back up any important information first.
5. Check for Physical Obstructions:
   • Make sure there are no physical obstructions around the TV, particularly around the infrared sensor on the TV and the remote control.
6. Contact Customer Support:
   • If the issue persists and your TV is still under warranty, consider contacting Polaroid customer support for assistance. They may be able to provide additional troubleshooting steps or offer a solution.
7. Professional Repair:
   • If the TV is no longer under warranty and the issue persists, it might be advisable to consult a professional technician or a TV repair service to diagnose and fix the problem.

Always refer to your TV's user manual for specific instructions related to your model. If none of the above steps resolve the issue, it's recommended to seek assistance from the manufacturer or a qualified technician for further diagnosis and repair.

See Hints and Tips section of manual on page 36. Your problem is discussed there. Help And Tips - Polaroid 19" HD-READY User Manual [Page 39] ' ManualsLib

MY polaroid smart tv has narration voice on it and I don't know how to turn it off

From a previous post and an answer from our Television Expert Larry, normally not worth repairing Polaroid televisions are made in China and are not made with quality components. Wow, they are only $239 new, what quality can you expect? His advice was to replace with mainstream brands like Sony, LG or Samsung.

Polaroid P50D300FP 50 Inch SMART Full HD LED TV ...

Electrical Deals https://www.electrical-deals.co.uk > brand-new-polaroi... Full HD resolution for clarity; SMART features for extra content; Freeview Play for a variety of channels; USB Recording to never miss a moment. £239.99 You can get boards for $10 https://www.google.com/search?q=P50D300FP(A)

No Model number, '50 inch' is just a size.Can it be fixed? Yes, they can all be fixed.Is it worth it? Unlikely. Polaroid are a camera maker and don't have a good name in televisions.Hopefully our television @Larry will be along to confirm.https://www.google.com/search?q=Polaroid+TV+50%22+fault+across+bottom+of+screen%2C+transparent+band+about+2+inches+high..

First is a link to a codes page. Next is a description of programming the device. The code page strikes me a little confusing about the method so that is why I provide the description of programming. Polaroid TV Universal Remote Codes & Program Instructions - Universal Remote Codes

1. Turn on your Polaroid TV.
2. Press and hold the SET button on your SANSAI URC-L969 universal remote until the LED light turns on.
3. Enter the 3-digit code for your device using the number buttons on your remote. If you don't know the code, try searching for it online or contact the manufacturer of your device.
4. Release the SET button once you've entered the code.
5. Test if your remote is working by pressing some buttons like volume up/down or channel up/down.

delete the Apps reset the television reload the Apps

Search for your TV model's official app or a universal remote app that's compatible with your TV.

You can't unless it has a 4 way directional pad with enter in the centre. https://www.fixya.com/support/r29872378-universal_remotes_no_facsimile_remote ..

maybe contact them here.... https://support.polaroid.com/hc/en-us/articles/360012600640-Sound-Bars-Sound-Posts-Sound-Stations