20 Most Recent
Bosch Nexxt 300 Series WFMC2201UC - Page 9 Questions & Answers
I am getting an E02
I've encountered this a few times. I still haven't been able to find out what the E02 stands for, but if you unplug the machine, wait 30 seconds, then plug it back in, it seems to work fine.
E13 won't spin or drain
Hi,
Problems with a washing machine not spinning or not draining are often interrelated..
If you are having a problem with your top load washer then check out thistip...
Washing Machine does not Pump or Spin
If you are having problems with your front load washing machine then checkoutthis tip...
Front Load Washing machine not draining and or not spinning
heatman101
I moved the washer from one state to another;
I will assume the noise is happening when you have water coming inot the machine.There may be a chance the water pressure is to high.you may also need to replace the water inlet valves.
Washer will wash but no spin
Hi,
Problems with a washing machine not spinning or not draining are often inter related..
If you are having a problem with your top load washer then check out this tip...
Washing Machine does not Pump or Spin
If you are having problems with your front load washing machine then checkout this tip...
Front Load Washing machine not draining and or not spinning
heatman101
Washing E-13 comes up
Timed out on drain cycle, basically you either have an outlet blockage or something is trapped in the pump, you can check the pump by opening the bottom right flap on the front panel,manually emptying the w/m and checking the pump filter for coins etc.
Good Luck.
Our washer will not spin during any cycle
Have you checked the pump and filter are clear? bottom right flap on front panel to expose pump. Check the hoses are clear, particularly if it is connected under the sink, via a spigot connection. If the machine has good motor action, but not spinning effectively, it will more than likely be a drainage problem.
I put a load of clothes in my bosh nexxt 300
Normal
0
false
false
false
MicrosoftInternetExplorer4
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman";
mso-ansi-language:#0400;
mso-fareast-language:#0400;
mso-bidi-language:#0400;}
This is for the WFMC6400, but it could help.
To manually unlock the door lock system, perform
the
following steps:
1. Unplug the power cord from the outlet.
2. Remove the lower toe panel.
3. Reach up along the inside of the front panel and
locate the bottom of the
door latch assembly.
4. Located on the bottom of the door latch
assembly is a teardrop shaped tab.
Gently pull the
tab down approximately 1/4 inch,
or until a click is heard.
5. The door may now be manually opened.
Pl give me a ‘very helpful’ rating for the free
help,
thanks!
What does E:27 mean
HI. This is a very common error code with this particular unit. The culprit will be the door switch. The main control module cannot recognize the switch, due to the damaged circuit at the door switch mechanism. These are plastic based components that tend to ware overtime, during frequent usage. The main
control module will not allow for a normal washing cycle while the door switch is in this state.The necessary actions are to have the door switch
circuit replaced, asap. Due to the complexity of this repair, i
recommend to seek the professional services of a local qualified Bosch technician. Mechanical and electrical experience is recommended.
- E-27 - Failed door switch circuit.(replace door switch circuit mechanism)
Mildew
take straight bleach on a white rag or towel and while wearing rubber gloves, wipe the surface until clean.
then run the towel thru a cycle with other whites ...
Bosch series 300 washer: E:04 error; how to remove pump cover
You can get that cover off, by prying it up at the bottom and spinning the thing clockwise. then there is a large hand turnable plug inside.
Once you turn it water will start leaking out, you'll have to get in and pull out the crud from the pump screen there to clear the jam. Good luck!
How do you open pump door?
The access panel on the lower front of the washer can be opened by prying up the lower side of it (near the small hole, I'm guessing repair guys have a special tool to do it), and at the same time twist the whole thing clockwise.
Do the reverse to put it back on.
Spin Cycle failure
Hi
Thanks for using FixYa. Washer not spinning can be caused by a bad
door lock mechanism and/or a faulty Timer. However, as you hear a hum noise
then you should also check around the drum as could be that the bearings have
worn out causing the hum noise. Please do accept the solution if the issue is
resolved else revert for further assistance.
Thanks
Rylee
Not finding what you are looking for?