Top 20
KitchenAid KHMS2050SSS Microwave Oven - Page 5 Questions & Answers
Mod.KHMS155LSS-1 Getting F-6 Fault code ????
Search Results
www.kitchenaid.com/...microwave...error-code...f6-error-cod...
KitchenAidQuestion: Combination Microwave Wall Oven - Error Code/Message - F6 Error Code -F6 E8. Answer. Product Symptom: Combination Microwave Wall Oven ...
www.kitchenaid.com/...microwave-error-code...f...f6...code/P...
KitchenAidKitchenAid's product help articles give answers to your frequently asked questions (FAQs). ... Microwave - Error Code - Starts with F - Starts with F6 - F6E0 Code.
www.shopyourway.com > Manage My Life > Questions
I have a Kitchen Aid Model # KEMS308SSS02 and I getting the follow error message... is working and was always working but the top microwave/oven does not work. ...Kitchen Aid Oven Model # KEMS308SSS02 error msg - Lost Err/ F6 E0/ ... Most "F6/E0" fault codes is usually because of a loose wire connections, loss of ...
2/5/2016 1:09:11 AM •
KitchenAid...
•
1,199 views • 0 helpful votes
How do I replace kitchenaid microwave door handle?
This is not a fun one if you take a putty knife and go in between the outer door and frame you can release the outer door cover hears the catch over time the door frame becomes brittle so there is a 50/50 chance the frame will break trying to separate it
2/18/2015 6:54:55 PM •
KitchenAid...
•
236 views • 0 helpful votes
How to change the torsion springs in my kitchenaid microwave oven KEMC308KSS01
Replacing the spring isn't very difficult if you're mechanically inclined.
You're basically removing a few screws, the front panel of the door is removed exposing only the glass part that's still hinged. The springs are exposed. Hopefully one spring is still in tack so you can see the orientation of how to put the replacement in. It's not very intuitive on how to do this part.
Check this link for more details:
Microwave Repair
2/12/2015 4:37:14 AM •
KitchenAid...
•
260 views • 0 helpful votes
How can I obtain a service manual for KitchenAid microwave KHMS1850S,need wiring diagram to interlock switches.
Pulled up a schematic on this will try and help the first pic looks as though you removed the secondary switch the bottom one if so that is the wrong switch it should be a normally open switch that one is normally closed this switch goes up top on the other side of the primary switch the one with 3 terminals, look at the second pic the switch with 3 terminals that red wire in the wrong spot the skinny orange goes there the switch I just told you to put up top the red goes to one terminal the white and brown middle form the 3 terminal goes to the other terminal, the blue/white and blue go to the bottom switch this is a normally open switch if you don't know how to read a switch look at the switch look at com follow the line to where it stops if it is NO=normally open, NC=normally closed your primary switch is in the right spot you want the switch next to it to be NC and the bottom switch NO it blew the 20 amp fuse once you correct the switches and wiring and put in a new fuse if you have no power then it blew past the fuse and burnt out the filter board happens some times about 60 bucks let me know if this helps
1/25/2015 10:09:28 PM •
KitchenAid...
•
402 views • 0 helpful votes
SPECS ON KHMC107B
Should be one of these. I expect manuals have specs. Cut and paste into your browser address line.
http://www.kitchenaid.com/webapp/wcs/stores/servlet/OCManualsLiteratureSearchResultView?catalogId=10552&langId=-1&storeId=10202
3/1/2015 6:31:34 PM •
KitchenAid...
•
131 views • 0 helpful votes
Kitchenaid microwave model KCMS1555RSS-2 door stuck, does not open
Hi Chan Sing,
If your microwave oven is brand new and under warranty then please take it to the place where you bought it from to claim for warranty.
If it over warranty then try this;
First off the power and unplug the microwave oven, open the screws off the cover and slightly lift and pull out the cover from the microwave oven. If you are not a technician then be care full what you are doing.
After you have removed the cover then you will see that at the place you posh the door eject button, behind it there is the mechanism that opens the door when you push the button from outside.
Now you have to analyse the simple mechanism if you are a non technical person, in here you will have to lift a small plastic up which we can call the lever. this is made up of plastic and it should be white in colour.
If you have any problem please let me know.
Regards
Ashwin
1/23/2015 3:26:37 AM •
KitchenAid...
•
184 views • 0 helpful votes
Not finding what you are looking for?