20 Most Recent Whirlpool Cabrio WTW6600SBK - Page 3 Questions & Answers

I believe you remove the lint filter and the rack fits in that opening and the rack will be in the dryer and won't be hit by anything when the drum turns.

http://www.theworldofwashers.com/2007/06/cabriooasis-f51-error-codes.html

F then 50 flashes when the motor rotor position sensor (RPS)
senses no rotation.
➔ Does basket turn freely? If not, determine cause of friction.
➔ If basket turns freely, see TEST #3, Page 10.
the above link is for code 51, very similar. the quite above is from the PDF manual. I just solved this problem on my machine. turned out it was clothing between the 2 baskets. Others have had bad control boards, or bad sensors

hi
The F51 fault code on these types of washers indicates that the machine control board detects an RPS (Rotor Position Sensor) failure. This sensor is on the motor at the bottom of the washer.
Here is the troubleshooting for the F51 fault code:

• Do not overload the washer. Overloading can cause this fault code.
• Check underneath the washer for any clothes or toys that could be under the washer and obstructing the motor from turning freely. This can occur because there is not a cover on the bottom of the Washer.
• Using too little water by choosing the wrong cycle for the type of load being washed can cause this fault code.
• Make sure that your drain hose is properly installed per your installation instructions. Siphoning of fill water out of the washer can cause tub resistance and will result in this fault code.
• Lift the lid and reach in and make sure that the basket turns freely. If not, you could have garments stuck between the two baskets or a problem with the basket hub. Any abnormal resistance to tub movement can cause this fault.
• Unplug the washer. Make sure that both the Control Board Connectors P5 (Motor Wires, red, blue and yellow), and the P10 (RPM Sensor Wires, 7 brown wires) are securely plugged into the Control Board.
• Remove the (P5) Motor Connector from the Control Board and take a resistance reading between the 3 combinations of motor wires (red/blue, red/yellow and blue/yellow). It should read around 32 ohms on the Motor Windings between any of the 3 pins on the harness. NOTE: If you do not get the proper resistance reading on the motor harness at the board, check the reading at the motor end. If you get a good reading replace the upper or Lower Harness whichever is defective. If the reading is still bad when checked directly off of the motor, then you will need to replace the motor. (See notes below for motor access.)
• Unplug the P10 connector and take a resistance reading between the two outside pins (1 and 7). It should read between 600 and 21.6K ohms. *NOTE: (If it reads open you will need to pull the Rotor and Stator so you can check it right at the RPS Sensor. If it reads good at the sensor replace the Lower, or Upper Harness whichever is open).
• To access the motor and RPS sensor, lean the washer back against the wall. Secure the washer with blocks if needed. Remove the rotor (1-bolt), and the stator (4-bolts). When you pull the rotor off, check to make sure that the thin plastic beads that run between each magnet on the rotor is intact and in place. This could cause an F51 code as it will no longer separate the poles of the magnet for the sensor to read them properly.
• Check your wiring connections on the motor and the RPS sensor. Unplug and then plug the wiring harness connections back in on these components 5 or 6 times. This will normally scrape through any possible corrosion or deposits on the connections. Tug slightly on the connections when they are inserted for the final time to make sure that they are secure.
• Reassemble the washer .

I placed a very detailed post on how to resolve this issue. If you are mechanically and electrically inclined, this will give you pretty much step by step directions. I also analyzed why this is happening.

Please disconnect power before any work...
chek this site below:-
http://www.theworldofwashers.com/2007/06/cabriooasis-f51-error-codes.html

hope your prob will b sorted out & u will b helpfull
all the best
regards

If it is a dryer with the lint screen on top place the two ends of the metal loop into the two holes closest to the plastic clips on the bottom of the rack. The clip the metal bar down into the clips and the multi-bent part of the metal ring are now atteched to the bottom of the plastic rack. Turn it over and place the metal ring in to the back of the dryer and the front lip of th plastic rack then hangs loosly over the lip of the bottom of the opening of the dryer. It will all tighten up when you close the door. Hope this helps

look up manual

most likely control bd although could be issue with lid switch

you can acesss hte pump assy by tilting the machine back, the drain pump is located din the back right corner, the left corner is strictly a recirculate pump. you an remove the clamps and remove any debris from drain pump, and replace yourself if necessary

a putty knife at the corners

En la pantalla de mi lavadora whilpool duet aperece 5d y la puerta bloqueada ;que significa?

Have you checked the condition of your tub bearings? If they are worn it can give you a ton of problems. There are several videos on YouTube that may help you diagnose your specific problems. I was surprised that this is a common problem with the Cabrio washer. There are tub suspension kits available that help keep your tub centered but I would check the bearings first.

Cabrio is a top loading washer!

Whirlpool Cabrio 4.5 Cu. Ft. 11-Cycle Super Capacity Plus

Some models you can get them, on some models you would need the whole main board. You might be able to go inside and find out if it can be tightened

Chattering could be a shaft bearing and if it got bad enough could have damaged the tub seal and makes it leak. attached is a price on parts if your interested http://www.appliancepartspros.com/07-tub-parts-for-admiral-aav7000aww.html

There is a spin sensor that is part of the shifter if this is wet it wont sense the spinning, hence wont spin, and if it is wet you mat need to replace the tub seal http://www.appliancepartspros.com/gearcase-motor-pump-parts-for-whirlpool-wtw5600xw0.html

Could be a bad stator http://www.appliancepartspros.com/motor-basket-tub-parts-for-whirlpool-wtw6200sw0.html

On the bottom you can see it by just tipping the washer , its a stand alone unit it can fit in the palm of your hand. Simple to take out 2 screws and two wire connectors. UNPLUG FIRST

Too much soap