20 Most Recent Kenwood KDC-MP205 CD Player - Page 7 Questions & Answers

desvio de llamadas se puso qe ago

El amplificador de audio se te quemo necesitas llevarlo a un taller para que te lo reparen.

1. Be in Standby mode
2. press Menu
3. Use joystick to up/down through the menu
4. when it shows display mode on, press the joystick in to change it... you might have to hold it in or tap it twice. Mine's touchy, sometimes I have to push it in twice on the menus.

Have you gone into the menu settings and turned on the AUX input?

If you hit the "source" button and AUX does not show up. It needs to be turned on.

Sorry about the delay, I missed the model number in the header. I have requested a copy of the service manual so I can give you the parts you will likely need.
Dan

hi TOC error sounds like its the laser is faulty. you could try a cd cleaning disc. this may cure the problem..


Regards

Mark
www.blueice-electronics.co.uk

look and see if there is a reset... usually a tiny hole you can push a pen point into...(lightly)

I had this same problem, you have to be in menu mode to turn off DEMO mode.

Push the left toggle in. It will go through different preset modes, then it will let you adjust things manually.

I find it helps to keep the Beep function (in the standby menu) on so that you can keep pressing the toggle and know when you're back on volume. It's easy to press by accident.

u might not of pluged the areal in wright take it out and clean it then plug it bk in

Try pressinf the reset button (small black/grey one) that you would need a pencil to do,

Also kenwoods have a cup built in the audio ic to disconect sould if wires are touching together, although you may have it wired right a blown speaker will cause this problem, if thid did happen you would have to press the reset button to get sound after the problem was fixed, if none of this helps, i would sugest relpacing the audio IC'

Don

You can call Kenwood support, they really do help!
The number is:
toll free 1-800-KENWOOD (536-9663)

The owner's manual is available here: http://inform2.kenwoodusa.com/manuals%5CKDC-MP2035.pdf The answer is on page 20. Can't copy and paste, and too much to type. Hope this helps, though.

Did you start from the "Standby" mode?

You'll need to turn the auxiliary function on in the setup menu. Press Source to put the unit in Standby, then press and hold the Menu button for at least 1 second. Press the control switch toward AM or FM until the AUX setting comes up, then press the control switch toward <<< or >>> to change the setting to ON. You can download a user's manual here: http://www.kenwoodusa.com/support/simple.aspx?men=2&M2=69

Question edited for clarity. Try the ideas in the videos https://www.google.com/search?q=Kenwood+Excelon+DDX9904S+DVD+receiver+reset ..

Me radio kdc2159b is displaying the ward call,how do i remove it

To reset a Kenwood 8070 receiver without a remote, you typically need to locate the reset button on the device itself. This button is often small and recessed, so you may need a paperclip or a similar tool to press it. Consult the user manual or look for the reset button near the power or input/output ports on the receiver. Once located, press and hold the reset button for a few seconds until you see the receiver reset. Keep in mind that this process may vary slightly depending on the specific model of the Kenwood 8070 receiver.

Kenwood KDC-138 Instruction Manual [Page 18]

ManualsLib https://www.manualslib.com > ... > Instruction manual If the "E-99". code does not disappear, consult your. nearest service center. IN (Blink):. The CD player section is not operating. properly. ? Reinsert the CD.

My Kenwood KDC-d301 is giving me a E-4 error message ...

JustAnswer https://www.justanswer.com > car-electronics Aug 9, 2010 - Hello, The issue is most likely that the laser lens in the CD player itself is dirty, and not the disc. It may have been initially caused by a ... 1 answer · Top answer: You need the Kenwood radio keys that came with the unit to slide it out of the dash. It sounds ... Missing: 138 ‎' Show results with: 138

I have a KDC 138. It is stuck on OCER and will not reset.

JustAnswer https://www.justanswer.com > car-electronics > 5lw8u-... Sep 27, 2011 - This actually is DCER - you have a blown speaker. The radio is sensing a ground on the speaker circuit. Check that and let me know. If you leave ... 1 answer · Top answer: Thanks for stopping by: This actually is DCER - you have a blown speaker. The radio is sensing ... Missing: E- ‎' Show results with: E-

Cd Player Unit - Kenwood KDC-138/138CR Service ...

ManualsLib https://www.manualslib.com > ... > Service manual Kenwood KDC-138/138CR Manual Online: components description, Electric Unit, Switch Unit, Cd Player Unit. Controls Fm/Am Tuner, The Changer, Cd Mechanism, ...

This Service Manual is probably close enough for dealing with the power supply https://elektrotanya.com/kenwood_dpx-8020md_sm.pdf/download.html https://www.google.com/search?q=Kenwood+DPX-8070mj+service+manual ..