20 Most Recent
Kenwood KDC-MP205 CD Player - Page 5 Questions & Answers
Its in a company truck and it says Protect just
If protect is coming up on the display, it means the system is detecting a short somewhere on one of the speakers and so is turning the amp off to avoid damage.
Check all the connections at the back of the amp to ensure they are not shorting, and at the back of each speaker, if nothing is found there, check each wire for damage, or a bare wire touching the body of the car
3/25/2010 12:22:26 PM •
Kenwood...
•
Answered
on Mar 25, 2010
Keeps flashing Protect
there is a short in one of the speakers,or the outputs in the amp blew.
unhook the speakers and try it.
if the protect stays on,the amp is blown.
in the winter when the defrost is run on hot,it can overheat the amplifier.
1/13/2010 8:09:50 AM •
Kenwood...
•
Answered
on Jan 13, 2010
How do i turn the aux on for my i pod
From the manual...
Selecting the Source
Press the [SRC] Button.
Keep pressing it till you see AUX or AUX EXT
Here is a link to the manual if you still need to look up other functions.
http://inform3.kenwoodusa.com/manuals%5CKDC-MP2035.pdf
1/12/2010 5:48:25 PM •
Kenwood...
•
Answered
on Jan 12, 2010
Car stereo not working
somthings wrong with your ignition wire run your stereos power on a toogle switch
1/12/2010 3:43:50 AM •
Kenwood...
•
Answered
on Jan 12, 2010
WILL NOT COME ON READS OUT PROTECT ON DISPLAY
if you lost battery power the head unit thinks its been removed or tampered with. You should have a code that came with the manual that you have to type in to unlock it.
it is a feature that deters thieves from stealing it because it is useless without the code.
If you do not have the code you will have to call kenwood with the serial number to get the code.
12/15/2009 8:27:18 PM •
Kenwood...
•
Answered
on Dec 15, 2009
Why does it say protect
This happens when there is a short on the speaker wiring. To protect the unit from getting damaged. Check all your speaker cable connections, and also the cabling for damage or loose connections that may be shorting out on other wire or metal part of the car.
12/9/2009 8:53:47 PM •
Kenwood...
•
Answered
on Dec 09, 2009
1988 ford f-150 trying to put cd player in but
Constant 12V+
Green/Yellow
Switched 12V+
Yellow/Black
Ground
Red or Black
Illumination
Blue/Red
Dimmer
n/a
Antenna Trigger
n/a
Antenna
Right Front
Front Speakers
6" Doors
Left Front (+)
Orange/Green
Left Front (-)
Black/White
Right Front (+)
White/Green
Right Front (-)
Black/White
Rear Speakers
6" x 9" Rear Corners
Left Rear (+)
Pink/Green
Left Rear (-)
Pink/Blue
Right Rear (+)
Pink/Blue
Right Rear (-)
Green/Orange
12/8/2009 4:22:38 AM •
Kenwood...
•
Answered
on Dec 08, 2009
How do i stop the demo mode
Go into standby mode and enter menu. find demo mode and press and hold button on right side the small one for 5 sec.
11/10/2009 4:26:32 AM •
Kenwood...
•
Answered
on Nov 10, 2009
When my car comes on protect flashes on my cd
protect... try resetting the unit (there will be a reset button on face of unit) if that is no help there will be a speaker shorting some were in car.. if you have tryed both i'd say there might be a problem with the unit... and do the basics like good earth etc
9/22/2009 3:21:55 AM •
Kenwood...
•
Answered
on Sep 22, 2009
My Kenwood car stereo stopped
Hi there,
This usually means there's a problem with the speaker wiring. You may have a defective speaker; your speakers may be mis-wired, or one of the wires may be shorted against vehicle metal.
Disconnect all the speakers from the deck and see if the error message still comes up then try to dissconnect it from battery power (It must be work as 99%). If it does, then the deck is defective. If not, re-connect the speakers one at a time until you identify the one that's putting the deck into "protect" mode.
Good Luck!!
Thanks
8/26/2009 7:24:14 AM •
Kenwood...
•
Answered
on Aug 26, 2009
Not finding what you are looking for?