Mitsubishi WD-Y65 65" HDTV - Answered Questions & Fixed issues

Ur tv does nt support 3D. U can still see 3D if connected to PC. With power DVD 11 u can able to watch anaglyph 3D.Dnt get confused any standard screen (e.g. CRT (big boxes with curved screen)) can view anglyphic 3D content.

sound s like you have a bad color wheel the wheel spins and then the lamp lights the lamp could be bad as well

Contact any service technician.

After replacement of bulb, lamp reset should be done. Have you did it? If you wish to get more details, check this link. http://electronicshelponline.blogspot.com/ Selecting the view option, either to Mosaic / Time slide, can be selected by the drop-down list, at the top left of the display window, will make surf easy. You can also do a search, by type in the brand name/model number/IC used, in the search box at the top right of the display window.

Two thoughts:First is this is a DLP set and the lamp may have failedSecond is it should have the self check which reads error codes---most of these sets that is the same:" After you turn on the set, and get the regular red blinky lights, hold down the Device and Menu buttons together for about 5 seconds.(then release both) The Power light will start to flash in a two digit sequence. For example, 3 flashes, then 7 flashes = 37. Here are the error codes, and the corresponding problem: 12 = No error detected, check power supply. 32 = Lamp Cover is open. 33 = Air filter cover is open. 34 = Lamp abnormality 36 = Light Engine (DMD or Lamp Fan stopped) 37 = Exhaust or Lamp Ballast Fan stopped 38 = Lamp Temperature High 39 = DMD Temperature High 41 = Short is detected 44 = DVI cable between FMT and Engine disconnectedThis is for a earlier Mitsubishi DLP but should be the same as your set as Mitsubishi rarely changes things like this.If you get the lamp abnormal it is likely your problem.

ogrady1428,

I would check the filter on the fan intake first. Remove it and carefully clean it with compressed air.If this does not resolve your problem then I would remove the lamp and inspect the switch in the vicinity of the door for problems. Be very careful reassembling the unit once the door is removed. The interlock swich must be positioned correctly or you will get an error message. I have a tip at http://www.fixya.com/support/r4168009-change_lamp_in_dlp_projection_tv which explains the problem and how to fix it.

Thanks for using FixYa and for the generous rating. We answer these questions for free.

hardrocko

Time to buy a new one.

Lamp is usually customer replaceable and instructions are in owner manual.I would to begin with (set unplugged) get at the lamp to inspect it--if shattered inside look for a replacement.Google the model number with "lamp" to see what is available.You Tube has video instructions for replacing lamps on most brands and models as well---not have to read just look.

WD-Y65 is NOT a 3D ready TV. You either have to change the TV to see the movie in 3D, or just watch it in 2D in you current TV.I have the same TV as yours. Current I connect a desktop PC to the TV via DVI port, and I watch Avatar using colorcode 3D(Amber/Blue) with Stereoscopic Player from www.3dtv.at It might be a way for you to enjoy 3D without change the whole thing, but it's an entire different topic.

what are you trying to connect to this tv?

Analog input switching circuit is not functioning.

sonsunny

better try replacing the coil or the ic if its blown up.

Hi,

After the TV has shut down, without pressing reset: press and hold both the Device (Input) and Menu buttons on the front panel until the green light starts flashing. It will flash a two digit code: 3-4, 3-8, 5-7, etc. You may have to let the TV shut down a couple of times (without pressing reset) before it will give the code.

Please post the code to help me determine the section of the TV that has failed and what it will take to repair it. It may be a good idea to repeat the test a few times to make sure the TV is giving the correct code.

Let me know.so that we could proceed.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Possibly lamp, and thermal sensor.

What are you talking about? Just replace the lamp, if that does not solve the problem, also replace the thermal sensor. Nothing else. If you've damaged anything, take it to a repair shop. We are Mitsubishi authorized.

With your remote you should have menu that lists changing tint, aspect etc... the power surge sent it back to factory default.

sounds like you need a new bulb, mine is doing the same and the lamp light is coming on.

You need to replace the lamp and ballast to correct this issue, may sure use an original lamp from mitsubishi , generic lamp last less than a year

check in the back of the set is a 4" cover with 2 screws the lamp has 2 screws is easy to replace.

My suggestion would be to check the status of the lamp. I believe that its gonna blow soon, as the symptoms seem like that.