20 Most Recent Audiovox Jensen In-Dash DVD/CD Receiver w/ 7 LCD Screen" Car Video Player - Page 6 Questions & Answers

tune the radio to 89.1

357968001898441

The model you gave is for the dc adapter. please state the exact model number of your dvd player.

Hello
Your Audiovox's Laser Picup Unit is in trouble. In payers, that can play both CDs and DVDs, there are different laser Beams from the same Laser Picup Unit, one have with a wavelength slightly differ to the other. When we insert a CD or DVD disc in to the player, at first the control system inside the players' circuit board will detect it, whether it is a CD, MP3 or 'DVD, by variying the wavelengths of the laser beam, and confirm it to be a CD, MP3 or DVD. Only after this detecting process, it will read its lead-in track and start to play.
In your CD player, now there is only beam that has the wavelength to play DVDs. Others are not working. That is why, it plays only DVDs and not others.
But before replacing the Laser Pick up Unit, you just replace its strip wire. Strip wire is one which connects the Laser Pickup Unit ot the mainboard. It has carbon conductors, instead of metal conductors. There is a chance to get a break in these conductors, even one of them break, will cause a problem,. As it has to move along with the laser pickup unit, when tracks the CD, the chance for a break is there. Just replace it first and see will it help you. It has clips on both ends, and after releasing the clip, it can be replaced easly. If this does not help, replace the Laser Pickup Unit, with same type and number. Insist on same type and number, as it is a critical component in your system. OK.

012345 worked for me

Default code is either 1234 or 0000
Providing they haven't been changed from factory defaults.

Hi, I'm sorry that i don't have a solution to your problem but I have the same problem. Maybe we can work through it together or maybe you've had some success? Thanks Eric

Is it possible that you antennae if faulty. Please check if the insulatiion is weak or the antennae is shorting to ground. This can make the signals go bad and make the set hunting and go back to search mode .If the antennae is fine then the problem could be in the front end stage of the tuner. You will require an expert probe to look for signal weaking in this stage but if you can open the set and cean and solder the areas closer to the antennae output. hope this helps. Good day

The radio has to be removed from the dashboard.

Then post ALL the LETTERS+NUMBERS on any LABELS, BARCODES or STAMPED IN THE METAL CASING

they any one of these two methods,, hopefully one will work

Power on, Keep tray closed, press setup on remote and press 0086000 you will see region free in lower left corner, power off.

or

Remove any discs from the player. Press the Setup button on the Remote. Then, again using the Remote, type in the number 1379. A menu where you can change the region code appears. Change the region code to zero to play all discs from anywhere

if those fail then

Open tray
Press 2812 on remote control.
A menu will appear on the screen.
Press ok button until region 9 is displayed or 0 is displayed or region 2 as well..

IF those fain then u need to email audiovox and request the instructions to change the players regions.. PS.. they will require serial number and where u brought it from..

Hello,

A car alarm that won't stop can be a frustrating thing for a car owner and anyone within earshot of the alarm. Turning the alarm off without your remote may not be as easy as using the remote, but it can still be accomplished.

If the button for dis-arming the alarm on your remote is not working, it is possible that the battery for the remote is dead, that's why the button is not responding. You can check the manual for your audiovox as it should state something about this.

Follow the below steps on how to disarm your car alarm without the remote control:

1. Use the key to unlock the driver's door from the outside. Often this will work with the passenger door or the trunk as well, although it will not work with every car or every alarm.
2. Place the car's key in the ignition and turn the car on to shut off the alarm.
3. Use a keyless-entry remote to unlock the car doors. Often the keyless remote, even if it is not connected to the car alarm, can stop the alarm through unlocking.
4. Use a keyless-entry remote to automatically start your car. Like putting the key in the ignition, starting a car disarms the alarm because alarms are not made to go off while the car is running.
5. Find the alarm component within your car's inner frame and disconnect the alarm wires from the alarm system. Cut the alarm wires about 1/2 inch from the alarm system.

Good luck.