20 Most Recent Linksys WRT54GX2 Wireless-G Broadband Router with SRX200 (LS-WRT54G2) - Page 7 Questions & Answers

on the back there should be a little hole with reset above it, Get a paper clip or pin and push it in the hole and you will feel a button click in.

Kept it hold down for about 10 seconds and you should see the lights start flashing and your router is then reset. If it doesnt reset the first time, try holding the reset button in a bit longer.

Good Luck :D

connect your router to computer with ethernet cable.
Then you can access it with following link.
for belkin routers http://192.168.15.1
for other routers
http://192.168.1.1
or
http://192.168.0.1


type user as "admin" and password as "admin" or blank or "password"
IF you are still not able to access then press RESET button for 10 seconds it is in back panel of router.
Let me know if you need further assistance.

Here's the link:
http://drivers.softpedia.com/get/NETWORK-CARD/OTHER-NETWORK-CARDS/Linksys-WRT54GX2-Driver.shtml

if you havent changed it in the past then the default one is written on the back of the router, just flip it and you will see WEP KEY written on the back. that is it.

Are you trying to run the CD on the MAC computer. CD will not work on the MAC computer. But you can set up the router manually without the CD. Are you able to go online on any other computer . If your router is already set up and you are trying to add MAC computer to the network then you don't need to run the CD. you just need to add the computer to the network. If you are trying to install the router for the first time then you can do it manually. Click Here for step by step solutions

It could be try upgrading the firmwre of the router. Set a port fowarding for the yahoo messenger

please check & use ealier post. there are many factors & causes for this issues that have been posted. if you need help after trying please reply.

There is a third party firmware you can use that will speed up your wireless connection. The linksys firmware sucks on wireless.

Check the manufacturer's website for the default access to the router configuration (maybe "admin" and "password") but I think the newer transmitters come wirth the wifi disabled out of the box and you need to configure it before you can use it.

If someone else configured it for you you'll have to do a factory reset and reconfigure the whole thing over again..

I have never used an xbox b4 but I assume it acts like a pc. You have to get the physical address for the xbox and manually enter every character into the router so that it you are securly connected. Thats the purpose of using physical addresses to connect only trusted devices

I would suggest to hard reset the router once. All lights flashing at once is not good news.
Thanks Ranjit

if you want for mobile than contact customer service gprs connection and save the connection for the phone Bhoshdina

first, your router wont look for your laptop. your laptop has to find your router. make sure your wireless card is activated on your laptop. right click on the icon where it says network cable unplugged. it should then say "view available networks". click on that and look for your network. if you need further guidance, write me back and tell me what brand of laptop you have. also, for the second tower, if you are trying to go wireless with it, then you need a wireless adapter.

You can always browse into your router through the wired connection and change it to something you do know.

Push and hold the reset button in for like 1-2 minutes then release it, it should reset the settings to default

Hi.
Hold the reset button on the router for 30seconds. Make sure that your power is on for router at that time. It wil make the router settings back to default. Access web interface from a browser (http://192.168.1.1)
By default the username is blank, and the password is admin. Click the Ok button to log in to your router.

You can use the web interface to configure the device instead of the software that comes with it. There should be a slip of paper that came in the box labeled 'manual setup' that will tell you how to do this. You could call (800) 326-7114 and have linksys support walk you through it.

HI! I bliv u are having some issue setting up ur router.. I will be more than glad to assist u. . here are the steps u need to do:
1. press the reset button on the back of the router for 20sec..while pressing the reset button, unplug the power plug and after 2secs while pressing the reset button plug it back in and press for 30secs after that unplug the router for 15secs then plug it back in..once all the lights are solid and ok
2. connect the ethernet cable to port1 of the router and the other end to the lan port of your computer..
3. pull up ur browser then type at the url:192.168.1.1.or 192.168.0.1 or u can check the routers default gateway by right clicking the network icon on the lower right of your task bar and click on status and it will show the ip address of the computer, subnetmask and default gateway, the default gateway is the routers ip address, once u type in to the url, it will ask u the username and password, by default the username is admin and the password is 1234 or just leave it blank
4. it will show the setup page of the router. u can set the router on the specific internet setup that u have.
a. if ur isp is a cable company, normaly u need to do a mac clone on the router setup page by cloning the computer that is reg to the cable company, how to determine it. ex. the computer that is reg to the cable company is a desktop or laptop, if this computer is connected to the modem directly and u can access internet.
b. once u determined it u need to connect this computer directly to the router and do a mac clone and set ur internet settings to auto-dhcp..then save the settings and after that, unplug to the power of the modem and router, plug in 1st the power of the modem then once all lights lit, plug in the router, then once all lights lit, try to pull up a browser that ur computer is connected directly to the router.. ur cable connection shud be, cable from the modem will go to the WAN port of the router and connect ethernet cable on port1 going to the lan port of the computer..once u can access the internet, u can now access again the setup page of the router by typing at the url:192.168.1.1 and u can setup the wireless settings, u need to create a ssid or wireless name and a security..
5. If ur isp is a dsl normaly they give u a username and password to connect to the internet, ur settings on the router should be PPPoe
6. If ur isp gives u a static ip address settings, u need to set the router to isp setup.
a. how to check the isp of the isp given to u..
1. click on start
2. run
3. type cmd
4. it will show a dos prompt
5. from the dos prompt type ipconfig/all
6. it will list the ip address, subnet, default gateway, dns server
this settings should be type in to the settings on the router for static ip addressing..
7. Once your done on the internet setting, go to your wireless connection settings and you can create a wireless network name or ssid, set a security by selecting wep, wpa, wpa2.
8. once all is set. save the settings and to check if your laptop can access the wireless network that you did, turn on the wireless switch of your laptop, once its on, it will show the wireless network icon on the lower right of the taskbar, right click it and select on view available network, the network name that u did should list, just select it and connect and it will ask for the password, just type the password and connect, you should be connected to the wireless network and have internet access..
9. If you are going to hook up your desktop to the wireless connection, you need to install a wireless network adapter, install the driver and do the same thing as u did to the laptop, for the desktop no need of turning on the wireless switch, once you install the driver correctly, it will show a network icon..
if you have any query pls feel free to get in touch.. good luck

On Windows XP
>>right click wireless connection icon >>view available wireless network >>click on change advance settings inte left(SP2) orAdvance(SP1) >>on top click on tab wireless network >>clear preffered networks >>Click on ADD below preffered network box >>Put in the details for the titles mentioned below Association(Tab) >Network Name (SSID) : put in your wireless network name >Data Encryption should be check >Network Authentication(Shared mode) should be unchecked >The key is provideded for me automatically uncheck it >put the network key and confirm it Authentication(Tab) >check Enable IEEE 802.1x >now uncheck Authenticate as Computer when computer info is available >now uncheck Authenticate as as guest when user or Computer when computer info is unavailable >uncheck Enable IEEE 802.1x >>click OK now it will start working enjoy

All routers need to have a ethernet cord from the ISP Device. Most people run Laptops Wireless from there routers or if its stationary run another ethernet cord from an open port behind the router to your laptop.