Top 20 Gemini PDT-6000 Turntable Questions & Answers

a new turntable is needed

I don't know if this model is direct driven or by belt. If it's belt driven then the belt could be fitted incorrectly, or faulty. Another possibilty is that there's a fault in the motor control circuit.

HELLO
I have just posted a cure for this deck, it is to do with the microswitches under the speed select buttons - they need to be replaced. Just repaired mine today - now there are no more problems selecting speeds.
If the speed goes back to 33 when the deck is switched off, this is because 33 is the default.
ALL THE BEST!

HELLO!
I don't think the problem is the actual stylus (needle), it sounds like the magnetic cartridge has become faulty in some way (it does happen). My advice is try another cartridge and stylus (borrow if you can). If the audio stays the same then it MAY be the wiring in the arm going through the plinth (deck) and these wires terminate to pins or a small pcb board in the turntable where the phono cables and arm wires are connected. There may be a bad connection inside.
Also, make sure your tonearm counterweight and anti-skate are set up properly as well as this can have an effect on audio.
I hope this helps as I have been into audio since I was a kid!

Clean Your Turntable with a microfibre cloth. Power off the turntable and unplug it for safety. Access the turntable's platter by lifting it off. Inspect the belt. If it's loose or damaged, consider replacing it. Amazon should have the belt replacements. If Your Record Player Spins Too Slow, Here's How to Fix It in 3 Steps - All For Turntables

It is strange that both won't open, something common to both, power supply to them? https://www.google.com/search?q=gemini+cdx+602+drawers+won%27t+open ..

measuring that voltage wont tell you a lot of information. You need to see signals in an audio circuit and those transistors could be MOSFET and or they cannot be tested while in circuit.

Much depends on the noise and where it is originating. The deck doesn't seem well thought of and it is unlikely the manufacturer has a spare parts service - unless you have the skills needed to locate and rectify the "noise", which could be electrical, electronic or mechanical, and otherwise restore the deck it would seem advisable to replace it.

Sorry we have no way to know were you are so how can we recommend a place to buy it?

It depends on what connections the laptop has. Most have an audio in socket. So you can use that. All you need is to find a audio out on the deck. I looked at an illustration and it has an headphone socket. So you could use that. Just keep the volume control low.

Well this website is showing the picture of it, but you will have to enquire if they are still selling it. It will just slide on and a screw will tighten it up. http://www.trusound.co.uk/P/409/Gemini+TWMT-3601604+Tonearm+Counterweight+ I can't find on the net anyone else selling parts for this model, still.

You could try this place http://www.trusound.co.uk/index.php?page_id=24

This is not an audiophile turntable. There is no provision for adjusting the vertical tracking angle. The closest you can come to making an adjustment is to place shims between the phono cartridge and the headshell.

http://geminisound.com/wp-content/uploads/2013/01/CDX-2400-FULL-MANUAL.pdf http://geminisound.com/wp-content/uploads/2013/01/CDX-2400-FULL-MANUAL.pdf

Is the unit earthed ?

Is there something 'special' about them? Power cords are common. Take one to an electrical supply store, radio Shack or just look around the house for an unused one.

Look in your control panel on your computer and check the sound settings. For instance I have Sound Max on my PC and the imputs have to be set on to listen to different sound sources. Also there are level controls on it that can be set to zero.

Hi! Please open the volume control icon located on the lower right of the screen and check out the auxillary. Mostly they are muted so you will need to turn them on. Hope this helps and thank you for using FixYa!

Hi,

It's depending on the brand you're using.
But for general you have to check your;
Battery
Frequenty of the handheld, same as reciever
Frequenty of the receiver, same as the handheld
Gain adjustment in the handheld.
Gain on the receiver.
Check on the receiver if there's any RX when you switch on the handheld.

Good luck,
Gerard

As far as I know, Gemini does not release schematics outside of their authorized service centers. If only one channel is out, you shouldbe able to A/B the two to find the problem components. If the side is completely blown, the most likely problem is the output transistors. Start with those and work back. If you need further details on the method, update this with any questions.

Dan