Top 20
Philips Magnavox MWR20V6 DVD Recorder/VCR Questions & Answers
My Magnavox MWR20V6 DVD VCR Combo shuts down,
Before anything, I would attempt to see what the E1 code signifies. But usually when those things just shut themselves down it is because of a serious problem in the power supply. I think it is time to go shopping.
I cannot get the VCR/DVD to record from my tv.
I have no direct experience but you should note no recording will take place unless the signal format is suitable/compatible. HDMI is a digital signal and your VCR/DVD will probably require an analogue signal.
A tv processes the digital into analogue but sockets at the back of tv sets tend to be input only. A minority of tv sets have two scart sockets, the second one usually providing an output sound and video of what is playing on the tv at the time.
I believe it is possible to buy a box that will convert digital to analogue or vice-versa.
We are trying to record
check the hours your set to record.
if your only getting 4 tapes done, expand the number of hours
may need new recorder
How do I connect old school dvd/vcr combo to LED HDTV?
Y is not compatible, it is one of the three inputs for "component" video which consists of Red, Green, Blue channels - RGB. The single yellow jack is "composite" video and the red and white are for audio. If your TV has HDMI inputs which are commonly used for HD TVs now, then you should be able to find an A/V adapter to convert the composite video and the audio to HDMI. HDMI carries sound as well as video. You may also find a composite to component adapter which will take the single composite signal from the combo device and break it into the 3 RGB signals for the TV. The thing is that the quality will not be HD for any of these, but then anything on VHS tape or home made DVDs will not be HD anyway. Try searching amazon and ebay, possibly newegg.
All the dvds I insert are reading disk error.
Sounds like it is time for a new unit. your problem is not worth fixing as it is either a failing laser pickup due to age, or the laser beam is caked with tar from smoking.
New blurays are quite inexpensive.
Please dispose of the unit responsibly.
Cant play recorded dvd on another dvd player
It seems that a product of DVD Player is fit for you: Xinfire
DVD player- It is is almighty region free DVD player software which is accessible to play
all region DVDs; supporting a number of video formats; its' strong
compatibility makes it compatible with almost all brand DVD drives
Recording error E454039000
please see your instru. manual and go to the section troubleshooting.and fix it. God bless yousee this possibles causes.
- Disc loaded upside-down.
- Transportation lock engaged.
- Dirty, scratched, or defective disc.
- Dirty or damaged objective lens.
- Loading (mechanical) not completed reliably.
- Damaged lens suspension or damaged lens cover preventing free movement.
- Dirt, gummed up lubrication, or damage in sled drive mechanism.
- Dirty/defective limit switch or sensor.
- Defective spindle motor.
- Spindle table height incorrectly set.
- Bad component in optical pickup.
- Cracks in ribbon cable to optical pickup.
- Need to adjust servo (or less likely, optical) alignment.
- Faulty power supply, electronics, or control logic.
- Bad connections including missing/erratic optical deck shield.
- External interference.
Power off when inserting vhs tape
I had this problem when copying an old family vhs tape. I had to unscrew
the top of the magnavox to access the vhs tape. Then, I gently removed
the tape and replaced the cover. After winding the tape back, I put it
in the player and immediately pushed fast forward for about 3 seconds
before hitting play followed by d.dubbing. I was able to make a copy of
the tape and did not damage my original.
My vcr tapes play too fast
If I remember correctly, VCR players had three speed settings. SP-short play, LP-Long play, and SLP- Super long play. The vcr is supposed to be able to tell what speed the tape was recorded at, thus playing it back at the correct speed. If your unit has lost the ability to sense the speed the tape was recorded then you will have to set the speed manually, if possible. Other than that I would have to say it's time to get a new vcr.
Magnavox vcr/dvd combo the vcr part only plays for 8 seconds
What you have is called a transport problem in the VCR unit--the mechanism is either jammed or something in it that loads the tape is bad.Every time it is used it cycles to self check the mechanism--if it fails it is usually a belt bad or a gear assembly not working.Someone would have to open unit to see what is happening.
How to record dvd from an led tv
Your TV must have a video and audio out RCA or S-VHS connector on it to be able to connect to the video and audio input side of your recorder.
MWR20V6 MANUAL
go please to www.fitness.manualsonline.com or www.retrevo.comor www.manualsfactory.comGod bless you
Programming codes to ATT remote
Check for codes by Device Brand. Not by remote brand.
For more details, just type in the site name "Electro-help" to
your search engines' search box [not in the address bar of your browser],
and click search. It is an electronic
equipments service help site. All
details you want are there. Note
the position of hyphen in between words in site name, when you type it
in. The site will appear as it
is in web; subtitled as Service help to electronic home entertainment
equipments.
Pull up older posts.
You can get all details.
You can locate it
either at the bottom part of first search page, or at the top of second page.
Detailed descriptions are there to help you.
Sometimes, clicking on advertisements by the side and
bottom of each post might help you to get details about the availability of
spare parts; price etc:-
Why will the power light not remain on and why does the recorder not recognize a DVD brand that has been used for the past two years?
HelloIt power supply regulator baord should be checked for any loose soldering points. Some coponents in it will heat up to an extent while the set works. Repeated heating and cooling may make solder points ot the components that get heated, and cause interruption to switching signals. Just take out the power baord, and resolder all the suspected doler points, by applying a little more solder, without making any solder bridge short in between adjecent solder points. If this do not help you contact the nearest Philips Authorised Service Center to get this set repaired. On rare occations, the supply board as card basis may be replaced. OK.
Not finding what you are looking for?