20 Most Recent Sharp AR-5320 Black and White Copier - Page 4 Questions & Answers

Apparently not. I have found it in UK English, though. http://www.sharpmea.com/cps/rde/xbcr/documents/documents/om/34_ppc/AR5316E-5320E_OM_Online-Manual_GB.pdf

the error e7 may have a variety of "sub-codes" attached to it, each depicting a different problem. hold the start button down to confirm the subcode. the following site offers the technical explanation of the subcodes: http://www.printcopy.info/?l=en&mod=free&chap=erc&brand=sharp&model=ar5320 that is what you asked for but i think the answer will be too technical when you look it up. but you might then google for a repair of that particular code and subcode and see what appears. for that matter, after you determine the subcode, i see no reason why to not contact the manufacturer's support and report the printer information and error code and see if they have a remedy. here is a site for downloading a manual for such printers. it might simply be a user manual. http://www.google.com.au/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&cad=rja&uact=8&ved=0cceqfjaa&url=http%3a%2f%2fwww.sharpmea.com%2fcps%2frde%2fxbcr%2fdocuments%2fdocuments%2fom%2f34_ppc%2far5316-5320_om_gb.pdf&ei=csravj7gmuxxmaxsk4hwda&usg=afqjcnedcbf1dnyg_j2h2rxi0ll5sxjrag&bvm=bv.83829542,d.dgy here is a fellow with a similar problem, an e7 error. but you can see that he was trying to clean the laser and probably disconnected something. http://www.copytechnet.com/forums/sharp/41980-sharp-ar5320-error-code-e7.html?s=84de82058651b6d355c5f09853183f36 good luck.

It will support windows 7, you can go to the link http://support.sharp.net.au/drivers/ and on photocopiers you can find ar 5316, download the driver for windows 7 then install it, rate this and vote for this.

U2 00 EPROM error 11 EPROM error





U2 04 EEPROM serial communication error 11 counter check sum error 12 adjustment value check sum error(EEPROM) 40 CRUM communication error

U2 04 EPROM error 11 Main counter error 12 EPROM error

U2 04 EEPROM serial communication error 11 counter check sum error 12 adjustment value check sum error(EEPROM) 40 CRUM communication errorYou need the service help. It is no a distans work Good luck)

there should be another half to that code it should scroll between a leter number and then number number ie E4-00 I would need the first half of the code as well to help you. I’m happy to help further over the phone at https://www.6ya.com/expert/ethan_e84416e0b13809d2

Whats your question here, are you needing help with installation or connecting or is it not functioning after installation

Code M2 means your photocopier machine require maintenance.In maintenance some old parts of your machine will be replaced with the new one and all this will be performed by technical services representative.

Service engineer req

fuser temperature issue, check thermistor and thermostat , Halogen heating lamp

check thermistor and thermostat

fuser error which could be a number of issues , press green copy button for sub-code

HI You have a door open somewhere, or no toner installed. Cheers

HI, Not sure what you mean by reset scanner, what problems are you experiencing? Cheers

Side door open. -check that all the side doors are closed. ok

"Press # - Interrupt - C - Interrupt -14 - then press start button then wait 30 seconds . If not work this way so please: Check thermistor. good luck :)

Remove the tank & pure down all the developer, use brush or a vacuum blower to remove the residual developer on the two sides joints where the roller rolls on the tank then turn it freely with your hand.sure. sieve your developer before you pure it back . thanks

http://www.sharpmea.com/cps/rde/xbcr/documents/documents/om/34_ppc/AR5516-D-5520-D_OM_GB.pdf

Look to make sure your developer is flowing evenly on the mag roller. Next I would check the scoretron\grid it is the saw tooth blade that faces the drum. I’m happy to help further over the phone at https://www.6ya.com/expert/ethan_e84416e0b13809d2

Hi 1. main charger shortage 2 drum in side ground contact no teach 3.ore toner damage

L6-10 is a bad laser unit. probably the polygon motor isn't spinning at full speed. check the laser unit using simulation code 61-1