Belkin Wireless G Plus MIMO (F5D9230-4) Router (1010835) - Page 4 - Answered Questions & Fixed issues

by default the Belkin does not have an admin password- if you are locked out, locate the recessed reset button on the router, and hold it in for about a minute- this would reset the router to its default configuration and security I’m happy to help further over the phone at https://www.6ya.com/expert/susan_42b401e0b1603d8a

You need to reset your router to defaults. You can also configure it with below method.
Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. Then click on WAN settings set it as your internet service provider settings enable DHCP Then click on wireless and enable it. . Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.

Make sure you choose the right protection.

WPA
WPA Personal

WEP

etc.
etc.

it depends on what you specifically want to password-protect: a. protecting the network from unauthorized users? b. protecting the network's admin interface?
for a. - log into your network's admin interface (usually http://192.168.0.1) - go to the category of wireless security - select the type of network protection you are looking for (strength - i.e. wep, wap, wpa2) and set your password following the steps listed within your router's admin interface...
for b. - log into your network's admin interface (usually http://192.168.0.1) - if you have never done this before, then your username should be filled in as Admin and leave password blank and hit enter.... from there, you are able to change or at least add a password to the interface from unauthorized access (usually under category security)

1. Click on "Start" in Windows XP. Go to "Run", and type "CMD" (without the quotes.) Click on "Start" in Windows Vista or 7. Type "CMD" (without the quotes) in the "Search" box.

2. Press your "Enter" key and you will be at the Command Prompt. Copy and paste the following command into your prompt:
Ipconfig /all

3. Press the "Enter" key to execute the command.


4. Look through the list of names until you see either "Default Gateway or IPV4 Gateway" and write down the numbers next those names. The numbers will look similar to 192.168.x.x

5. Open Internet Explorer and erase your homepage address from the address bar. Type in the Gateway IP address you wrote down, and press "Enter". This will bring you to your router configuration page.


6. Enter your router password. If you do not know the password, open a second Internet Explorer window and search for the default password for your router.

7. Click on the "Administration" link on your router, look for a setting called "UPnP" and change it from "Disabled" to "Enabled".


8. Click the "Save Settings" or "Save Changes" button at the bottom of the page. Exit your router configuration and you will have an open NAT.

Sorry dont have a Belkin router with me but this should be explicit enough for you to be able to look for the UPnP and do what i said.. If possible send me a screenshot of the Router interface i will help you more with it if you cant..

Hi,

Welcome to Fixya. The security key can be found when you access the wireless settings page of the router. To access the router page you need a working computer that is connected to the router. To access the router page just open a browser then type 192.168.2.1, the Default password isblank.


Click on Security under Wireless and look for the Security Key or Network Key (Passphrase)


If you have questions please let me know. Thanks for using Fixya

Connect a LAN cable from Belkin to your laptop/computer'sLAN port, open a browser on your laptop/computer and enter the Belkin'sconfiguration URL. http://192.168.2.1
The default PW = blank (just press Enter) You can now change the default password.
You can now configure the wireless settings. Now configure the wireless card in your computer/laptop withthe router's wireless settings.
To secure your wireless network from unauthorized access,please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

If there has been a password already set that you don't know you will need to reset to factory defaults. If there isn't one look here: http://portforward.com/default_username_password/Belkin.htm and find your router and try the default username and password. If you do end up resetting to factory defaults then look at the link above and use the default username and password to get into your router.

click here to know how to find or create or change the password of your belkin router.


My entire list of useful tips... click here

For any further assistance comment here...

Dear user,

Looks like you are loosing the link , please try to move towards the Wireless transmitting device where it is installed. it will increase the signal strength, if you cant move away, keep your laptop such that its not blocked by cupboards, walls or any big objects

Connect a LAN cable from Belkin to your laptop/computer'sLAN port, open a browser on your laptop/computer and enter the Belkin'sconfiguration URL. http://192.168.2.1
The default PW = blank (just press Enter) You can now change the default password.
You can now configure the wireless settings. Now configure the wireless card in your computer/laptop withthe router's wireless settings. Connect a LAN cable from your DSL or cable modem to the Belkin's WAN/Internet port.

To secure your wireless network from unauthorized access,please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

You can also configure it with below method.
You can configure it without disk with below method. Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. Then click on WAN settings set it as your internet service provider settings enable DHCP Then click on wireless and enable it. . Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.

1. network security is setup by the user
You either have it or you will need to go through the set and establish a new network security key again via the CD that came with the router device.

you need to setup your xbox 360 with a static ip address
after that login to your belkin router
and click on virtual server on the left.
then add the following ports 53,80,88,1863,3074.

Protecting your network with WPA/WPA2 security

Setup steps:

1. Connect the computer to one of the four LAN ports on the router.

2. Open a web browser on the computer.

3. In the address bar of the web browser, type http://192.168.2.1

4. Click Login in the upper right-hand corner of the page. The router does not ship with a password, so just click Submit.

5. Click on Security in the left-hand column under the Wireless heading.

6. Use the drop-down menu and select "WPA/WPA2-Personal (PSK)".

7. Select either WPA-PSK, WPA2-PSK, or WPA-PSK+WPA-PSK2 as your Authentication; doing this will set the Encryption Technique automatically.

8. Enter a word or group of characters in the password (PSK) box. The Pre-Shared Key must be 8 to 63 characters in length. Note: The PSK (Pre-Shared Key) is case-sensitive ("A" is different than "a").

a. Unchecking the Obscure PSK box will allow you to see the security key that has been typed.

9. Click the "Apply Changes" button to save the settings.

Any/all wireless computers that connect to this network will be required to have this Pre-Shared Key (password).

Hi,

Welcome to Fixya. To access the router page you need a working computer that is connected to the router. To access the router page just open a browser then type 192.168.2.1, the Default password is blank.

Click on Security under Wireless and look for the Security Key or Network Key (Passphrase)

If you have questions please let me know. Thanks for using Fixya.

On the back or bottom of the router (depends on the model) there is a reset button. press that and hold it for atleast 30 seconds while theitem is plugged in. This will reset the modem. After that you need to reset itup liek you just purchased it.

• You can configure WEP or WPA. But you cannot enable both at the same time.
• You can configure MAC Access Control list and also enable WEP or WPA for additional security.
• After you enable wireless security features on the router, you must configure your wireless clients with the matching settings. Your wireless clients will not be able to connect to your network unless you configure matching settings.
• It is recommended you enable these wireless security settings from a computer wired to the router.
• 1. Connect a computer to any one of the four LAN ports of the Belkin wireless router.
  2. Open your web browser and type the router IP address of the router (by default, the address is http://192.168.2.1.) in the address bar and press Enter.
  3. Click Login on the top of the page to login to the router. By default the Password is left blank, click Submit.
  4. Click Security under Wireless menu.
     1. Under Security, Select 64 bit WEP (or 128 bitWEP).
     2. Select Key 1 and enter any 10 hexadecimal digits - any combination of 0-9, A-F (26 digits if you selected 128-bit as the encryption strength). You may also enter a pass phrase and have the router generate a key for you.
     3. Apply the settings. Please write down the key - You will need it later to configure your wireless computers with the same key.

1-In order to get your router back to the original settings, you must push in the reset button (usually on the back of the router) for somewhere between 10 and 30 seconds depending on the router. You may need a pin or something small to push in the button, because it can be recessed. Once you have reset the router, the username and password will be changed to the defaults, admin and password, respectively. One thing you must remember is that resetting the router will change all of the router settings back to the factory settings. This means you will lose all of the changes you made since you got the router. Make sure to write down any things you've changed, so you can change them back after the reset. Also, I recommend updating to the latest firmware after the reset.

2-There is a great article at Working with Windows Wireless Networks
If you need more help post back! Thumbs and testimonial are welcome!

3-There a great article at General Router Setup.
If you need more help post back!
Thumbs and testimonial are welcome!

yes can instaal in wirlles connecthoin active