Belkin Wireless G Plus MIMO (F5D9230-4) Router (1010835) - Page 2 - Answered Questions & Fixed issues

Did you restart your computer? If so, I'd power down everything (modem, router and computer) and restart them in that order - modem, router, computer. My guess is that the router and computer addresses are not in sync.

Is this a new router - or should I say did you only have the one computer hooked to the modem until now? Some ISPs use the MAC address of the installed PC to assign the network IP address. Since the Router will have a different MAC address, the modem will not recognize it. ISPs use this as security, but it makes networking impossible. However, most routers have a feature called MAC spoofing, which allows the Router to fake the modem into believing it is the computer originally attached to the modem. On newer routers this is a feature that can be automatically done during the setup wizard. You need to have the original PC hooked to one of the router ports (not WAN or INTERNET) and when the router asks you if you want to use the MAC spoof, say yes.

Most routers can be setup by typing their IP Address in the address bar of your browser. So long as your router is connected to your modem and your computer is connected to your router that is.Typing

192.168.2.1

into the address bar could get you to the login screen of your router. Then you would just have to enter the user name and password. You might even be able to access a wizard from there to help you set up your router.If that doesn't work you could try 192.168.0.1, 192.168.1.0 etc.

i'm not sure with your question.every wireless has it own default username and password, does'nt it? just press the reset button and connect to it with the ip, username and password that you can read on the back of your wireless

http://network-magic.software.informer.com/

You need to encrypt your wireless router. Connect a LAN cable from Belkin to your laptop/computer's LAN port, open a browser on your laptop/computer and enter the Belkin's configuration URL. http://192.168.2.1 The default PW = blank (just press Enter) You can now change the default admin password. You can now configure the wireless settings to protect your wireless network and Internet from unauthorized access. Now configure the wireless card in your computer/laptop with the router's wireless settings. To secure your wireless network from unauthorized access, please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

This may help: http://www.belkin.com/au/support-article?rnId=7802

I would suspect the other devices, what every they may be.

Use the reset button near where the AC adapter plugs in. Hold it in for at least ten seconds. This should set it back to factory, allowing you to set another password.

You Can Try Changing the Wireless Channel on the Router you have 11 Different Channels Available.

> Steps to change the Channel

- Open Internet Browser on Hard wired computer & Go to 192.168.2.1

- Towards your Left Corner Under Wireless Click on Channel & Ssid

- Leave the Password Blank Click on Submit

- Change the Wireless Channel To Number 1 or 6 or 11.

- Click on Submit

- Check the Signal Strength

- If you Still Have Low Signal Strength you Can Try Updating the Firmware or Changing the Wireless Mode to G only... :)

Unfortunately the range on a G router is usually reliable to about 200 ft or so, depending on obstructions. There is no way to boost the 802.11g signal. You'd be looking at upgrading your router and card to 802.11n, which would give you increased range. .

if your in a metal shed then the best way would be to mount a outdoor type access point to boost signal or just hardwire it

Have you attempted resetting the router?

There's a small hole in the back of the router. Find a paperclip, unravel it, then stick it into that hole. Once inserted and you know the paperclip has reached the end of the hole, press in. Hold it in for about 30 seconds and the router will be reset.

NOTE: Resetting the router restores it to factory default settings (most of the time). This means any settings you have changed since then will have been erased! Reset the router at your own discretion.

If resetting the router doesn't do the trick, let me know. I'll find some instructions for forcefully accessing the control panel.

When changing the advanced settings on the Belkin router, you should change the default password.

To change the password, go to Administrator Password. Type in a new password. Make sure you remember the password, otherwise, you will need to reset the router back to default settings.

I hope this helps.

You may need to change some settings on the router.Also you may need to open the ports on the router for PS3.If you are using DSL Internet service then make sure that modem is in Bridge or PPPoE mode.Read How to change NAT type to open for gaming devices

You can find the wireless password also called wep key or wpa pass phrase through the set-up page of the router. If you don't know how to access it, follow the instruction in How to Access the Router's Setup Page (just click it.)

When you added the WPS encryption ket to your wireless router, this secures your wireless network from unauthorized access to you wireless network.To allow your wireless computers and wireless printer to communicate with your wireless network the wireless cards in the computers and printer needs to be configured with the WPA encryption settings that you configured in the wireless router.

To access Belkin's web based setup page type 192.168.2.1 on the address bar of the browser.And if you can follow this web link to setup a static Ip for your DVR , in case if you need further help you can contact me directly ..http://www.corenetworkz.com/2009/07/setup-belkin-wireless-n-router-by.html

sounds like you need to reenter the password/key
go to network connections and disconnect from it. then try to reconnect after the refreshes.
is it asking for a password/key?

hold the reset button in with a paper clip for 30 seconds whiled powered on.go to 192.168.2.1 in ur browser. the password is blank. reconfigure settings to your desire.