20 Most Recent Magnum DeltaForce CB Radio - Page 2 Questions & Answers

Try this, looking at the mic connector from the wire side and going counter-clockwise starting in the four oclock position: PIN 1 sh, PIN 2 wh, PIN 3 bk, PIN 4 rd.

please follow this steps and fix it. GOD BLESS you

• 1

Turn on all of the devices in your sound system. Turn off any auto-equalizers on your sound system to gain fullest control over frequencies. This switch might be found on the receiver or the equalizer itself.

• 2

Play a test song on repeat. Choose a song with both extremely high and extremely low instruments so that you have a wide frequency range to listen for.

• 3

Listen for any obvious distortions in the highs and lows of the songs. Lower the knob on your equalizer for any distorted frequencies until the distortion disappears. Try at first to find the highest setting possible without distortion.

• 4

Adjust all frequency ranges in relation to each other to find a pleasing blend for your room, trying not to let any one frequency range dominate the others. Use the highest non-distorting settings found in Step 3 as maximum settings, but don't be afraid to lower a booming bass or a screeching flute that disrupts the overall blend of the music.

• 5

Play a song from a different genre to test how the EQ works for different types of music. A hip hop song will have louder lows than a string quartet, for example, so make sure your bass frequencies sound crisp on both types of music.

match up the wiring diagram on the mic to the wiring on your radio.www.cbtricks.com

ground them out and you will find them

What antenna are you using? What is the SWR on the antenna? Note that the swr wont necessarily affect Transmit but it will show if there is a general antenna problem like a short, that could be causing this. Otherwise it is an issue that needs to be diagnosed in depth on a test bench.

0 = Transmitter Timeout timer has timed-out 1 = Transmit Frequency is lower than TX Lockout Lower Limit 2 = Transmit Frequency is greater than TX Lockout Higher Limit 3 = Phase-locked-loop (PLL) won't lock at this transmit frequency 4 = PLL is intermittently coming out of lock during transmit*If your radio displays error 3 or 4, don't keep trying to transmit on this frequency. The cause of the problem could be low power supply voltage to the radio or the radio's VCO loop needs adjustment. Refer to a qualified technician for service. Contact the installer of the chip first. If, however, you installed the chip yourself, contact a qualified technician for service.

red and sheild 1 pin
white 2
blue 3
black 4

http://www.cbtricks.com/

hi i have a gold eagle mark 4 i like two put a 776 back on it but i do not know the wiring coad thank you .

You might have accidentally put it in to ham Mode i think Turn Off radio Hold function And Mode Buttons If I remeber Right

they make an adaptor, check ebay. i just got one for my d104 4pin to rci 6 pin. 5bucks free shipping.

Same as Omega
#1 Mic Audio
#2 Receive
#3 Transmit
#4 Up/Down for channels
#5 Ground/Shield
#6 13 volt

I am assuming the conversion you wanting is radio plug not mic.I would suggest an adapter but the conversions that i know of often result in pop, chirps or modulation issues so i would avoid condensing wires. There are gounds and there a floating grounds. Your receive could be adversely affected even with this adapter. http://www.copper.com/cart/product_info.php?cPath=36_38&products_id=670Hope this was of help.

• Here is a copy of the Magnum Delta Force owners manual for you http://minus.com/mbnSzcHKIl Browse through it and feel free to ask me any questions you may have.

• Hope this helps.

• Here is a copy of the Magnum Delta Force owners manual for you http://minus.com/mbnSzcHKIl

• Hope this helps.