Top 20
Frigidaire Affinity ATF7000E Front Load Washer Questions & Answers
Hi, I recently purchased a 6 year old condo and
The result of cool water temperatures and milder detergents, is a buildup of oil and grease in the machine, which produces oily smells in the laundry. Grease and oil can take many forms, ranging from automotive lubricants to greasy foods to oily toiletry items, and, over a period of time, these oils can accumulate and become trapped in various parts of the machine, particularly in the door seal of front-loading machines.
Run an empty cycle with HOT water and a detergent that contains bleach to remove grease and oil from the appliance. However, be sure to use bleach designed specifically for laundry, as opposed to using regular bleach. ie OxyClean. and or a cup of vinegar.
Best to you.
2/26/2018 4:18:03 PM •
Frigidaire...
•
468 views • 0 helpful votes
My Frigidaire Affinity ATF6000FS1 front
It's the timer control, not the motor or filter. Try a different setting. You should also be able to find more information on the manufacturers website, along with a manual and possibly a diagram. Also You Tube is a good place to find out more on how to repair it.
12/3/2017 7:54:04 PM •
Frigidaire...
•
523 views • 0 helpful votes
I have a Frigidaire Front Loader Washer Model #
You need to lean it back and remove the lower panel, you will have complete access to the water pump, disconnect hose clamps,remove and clean the rubber boot,disconnect electrical connector and 2 screws holding pump, Replace with new pump, before beginning take pictures to ensure proper installation
11/19/2017 6:30:04 AM •
Frigidaire...
•
542 views • 0 helpful votes
Washer quit working in middle of cycle, won't even come on
Look under the washer. Is there a little pile of black rubber shavings? With the heavy load, you may have broken the basket coupler between the motor and the drum. Try turning off the selector, and move it one click at a time towards the end of the cycle and turning back on. Hopefully it will drain for you. If the coupler is the problem it is inexpensive to fix. Some also call this part the "clutch". It kind of looks like a hockey puck with six holes in it... three for the motor, three for the clothes drum.
I attached pictures of a couple types. This part is a common problem when you put a heavy load in, because the rubber takes more stress.
7/9/2017 8:09:03 PM •
Frigidaire...
•
133 views • 0 helpful votes
Washing Cloth Diapers with Extra Ingredients
You can strip cloth diapers to help bring back absorbency. I use a simple method of washing clean diapers in the hottest temp possible with blue liquid Dawn dish detergent (1 teaspoon for HE washer, 1 tablespoon for older machines). I also add 1/2 cup bleach because it disinfects and sanitizes. Bleach has always been safe for me but im sure there are alternatives if you don't like bleach. Then a few hot rinse cycles and a regular dry cycle and diapers are more absorbent and odor free.
3/29/2017 2:18:04 AM •
Frigidaire...
•
148 views • 0 helpful votes
Nf code and donnot continue to next cycle
www.appliancerepairlesson.com/.../samsung-washer-
error-
code-
nf-fixed/
Jan 11, 2014 - What does the error code NF mean on a Samsung washer? ... You can set the washer to any cycle and test each solenoid for proper voltage. ... Next would be to check the screens on the back where the water hoses connect. ..... Hi, you don'thave any power to the water valve wires when it should be filling?
12/15/2015 6:46:20 PM •
Frigidaire...
•
819 views • 0 helpful votes
Why machine wont fill?
Hello. Do you have a well for your water supply? If so, turn off the cold water to the washer and remove the supply hose from the back of the washer. Check the inlet water screen for blockage due to sand, sediment, or other debris. It's a fine filter so BE CAREFUL if you have to remove it--don't damage it at all! It protects the precision valve from debris getting caught and jamming the valve. Next, you will have to remove the top cover of the washer if the screen was clear. Locate the cold water valve assembly(pic 1, part 36) and check to see if 120v is at the valve coil when the washer is supposed to be filling. If the voltage is there, the valve is defective. Also, and more hidden, is the possibility of a defective water level sensor--(it's about 1.25 inches wide by approx 3 inches long), it will have a small wiring harness attached to it, it's mounted on the right side, approximately 6 inches or so from the back wall of the washer and has a black rubber tube attached and running down the back of the tub to the air chamber at the bottom. (see pic 2 and 3) This sensor can fail in 2 directions--it can either think there is water in the tub already and the washer won't fill or, most disastrously, constantly think there is *no* water in the tub and flood your house. The former can happen if the air chamber gets clogged with mold/mildew. The latter can happen if a pinhole should develop in the pressure hose(air pressure never builds up to tell the sensor to tell the main board to stop filling!)To check the latest stored error code, press and hold the start/pause and cancel buttons simultaneously. The error code will appear as long as the buttons are held.
E11 is fill time too long (either a clogged screen or defective valve)
E31 Pressure sensor communication error
E35 Pressure sensor indicates water overfill
PART NUMBERS
MAIN BOARD 134556600
DISPENSER VALVE ASSEMBLY 134371220
ANALOG PRESSURE SWITCH 134407800
I hope I helped you!
12/20/2015 3:01:48 AM •
Frigidaire...
•
213 views • 0 helpful votes
What is the ltf7000es0 error code E66
Hello friend, thank you for your post!
I understand that your Frigidaire washer is displaying an error code of "E66". An "E66" code stands for heating element relay failure. This could be a problem with your heating element or control panel. In order to properly locate the issue you would need to disassemble your washer and test each electrical component to assure it is providing an accurate reading. This is not a simple DIY job. I would recommend having a professional technician for proper diagnosis and repair. I hope this information is helpful. -Matt
5/5/2015 6:10:46 PM •
Frigidaire...
•
543 views • 1 helpful votes
Not finding what you are looking for?