20 Most Recent Frigidaire Affinity ATF7000E Front Load Washer - Page 5 Questions & Answers

The rear bearing for the drum needs to be greased. If you don't grease it and ignore it, eventually the dryer will stop working because you will be overloading the motor, and the motor will start drawing additional current that it will trip the breaker. Greasing the rear bearing is a 15 minute job. You need to purchase high tempo grease. Frigidaire sellsthe high trmp grease that is required.

Most likely suspect is the heating element. Part runs under 100 dollars. If you can't do the repair yourself, prepare to spend at least twice that amount.

Hi, Unplug the unit from AC power for 30 seconds to 1 minute, This should reset it back to the defaults. Good Luck!

mi lavadora da e91 y key stuk que hago

Hello Friend, thank you for your inquiry! Based on the symptoms you are describing, it sounds like your Frigidaire washer may either be experiencing a communication error from the main control board or the timer itself may not be operating correctly. Do you notice a humming noise? If so, then it may be a clogged drainage hose or pump that needs to be cleaned, or it could possibly have another issue with the door lock assembly. I would personally contact a professional to accurately diagnose the washer to determine the root cause to reduce the risk of unnecessary parts. Best regards! - Z

Hello friend, thank you for your post!

I understand that you would like to remove the front cover on your Frigidaire washer. Your question is labeled under model ATF7000E I was able to locate the parts manual for that appliance that shows a parts breakdown inside of your washer but no instruction guide to disassemble the front panel. I hope this information helps to some degree. -Matt Frigidaire Manual Search Results

Hello friend, I appreciate your post!

If the control panel is not lighting inside of your Frigidaire washer it could need to be replaced. I would recommend reaching out to a professional, if you do not have a professional connection you can visit the manufacturer website to find a service provider in your area. Hopefully this is helpful. -Matt

Hey friend, that's a great question!

It sounds like you may have an issue with the door strike or door latch on your Frigidaire front loader. I would recommend contacting a professional to come out and properly locate the reason to why your door is unlocking before going into a cycle. -Matt

Vanessa, I will share a link with you that may put you happy and enthusiastic. It serves, as well as, a contact point for reasonably priced parts ; should you need them. Frigidaire Affinity Washer Disassembly . Take a look. And please share how you finished. Fare.Well.

To Stranded, Here is a link that will put you directly to free support and a manual to guide through the trouble shooting function. sparke needs help with Frigidaire Washer on ManualsOnline com . If you are familiar with a meter to troubleshoot and identify voltages. Start there. If the display is functional. Here is another forum you can tap for resources to compare. Basics first. How to enter diagnostic mode on Frigidaire ATF7000 washer Appliance... . And you will need to take it apart.. here is the link for that solution. Frigidaire Affinity Washer Disassembly Say how you made out and if this approach helped please? Fare. Well.

Hello friend, thanks for your post!

It sounds like it could be a possible issue within your control panel or door lock assembly. If the door is not making that connection it is closed the washer will not start. I would recommend having a professional come out to properly diagnose your appliance to avoid any unnecessary part purchases. -Matt

Hello keisha, thank you for your post!

I understand that your Frigidaire washer is making a buzzing sound until the cancel or start button has been pushed. It sounds like it could be a possible issue within the door either not being fully closed or it could be a defective switch. I would recommend resetting your appliance which can be done by disconnecting power to the appliance for roughly ten minutes. Please comment back if that did not help correct the issue. -Matt

Good Afternoon Friend, this is Z. I am happy to assist you! If your washer continues to PAUSE, it commonly indicates that the door of your washer is not securely latched or the cycle has been interrupted. Try pressing "PAUSE/CANCEL" or "START/PAUSE" once to resume cycle. If these basic troubleshooting tips prove ineffective, try reprogramming your appliance by unplugging it or flipping the household circuit breaker off. It is best to wait approximately ten minutes and then turn on your washer. If the issue persists, then your washer could possibly have a faulty door latch or experiencing a communication error with the control board. I would personally contact a professional to accurately diagnose your washer to determine the root cause to reduce the risk of unnecessary parts. Best!

clean it by using 5 cups bleach fill soap cup put rest in tub wash in hot water long cycle run another or 2 after to make sure bleach is gone

Hello Larry Occhipinti, thank you for your post!

If you are pushing the necessary buttons on your Frigidaire washer to perform a system clean and they are not working, it could be a possible issue within the control panel. I would recommend a reset on your appliance which can be done by disconnecting power from your appliance for roughly ten minutes. If that does not correct the issue, you can run a hot water wash cycle with a cup of bleach inside the tub to clean your appliance out as well. I hope this is helpful. -Matt

Hi Friend, thank you for your inquiry! If you are receiving an error code PAUSE, it commonly indicates that the door of your washer is not securely latched or the cycle has been interrupted. Let's try pressing "PAUSE/CANCEL" or "START/PAUSE" once to resume cycle. If these basic troubleshooting tips prove ineffective, try reprogramming your appliance by unplugging it or flipping the household circuit breaker off. It is best to wait approximately ten minutes and then turn on your washer. If the issue persists, then your washer could possibly have a faulty door latch or experiencing a communication error with the control board. I would personally contact a professional to accurately diagnose your washer to determine the root cause to reduce the risk of unnecessary parts. Best - Z

CLARIFICATION OF THE SIMPLETONS (LIKE ME) OUT THERE... It appears that everyone is correct. The outlet is indeed clogged, resulting in the e20 code. The most likely culprit is the primary reservoir: a black rubber catch found just below the clothes bin. It is mounted to the bin via two hoses - large and small - and secured by hose clamps. The catch is best accessed from the BOTTOM of the washer. That's right - you'll have to lay the washer on its side. I found that RIGHT SIDE DOWN was best. There is a large oval hole in the bottom of the washer; you should be able to see the black rubber catch easily. Detach the larger hose from the bin by loosening the screw-type hose clamp. Then, carefully raise the catch toward you to look inside it (a flashlight helps here). By doing this, you should be able to remove most foreign objects and remove any major clog. It was completely successful for me today... removed my wife's bra pad and several coins which were causing the washer to stop at the initiation of the spin cycle. After re-assembly, I placed the washer upright, connected all the hoses and plug it in... it worked perfectly! I ran it through a couple rinse/spin cycles to remove the remaining lint and minor debris. And, more importantly, I respectfully "urged" the wife to avoid placing such things in the washer in the future! Good luck everyone. This process should only take you about half an hour if you have plenty of space to work, like I did.

Good Morning Friend, this is Z. I appreciate your post! From what you have described, it sounds like your washer cannot properly drain and dispose of the water and detergent solution. Does your washer make a humming noise? If so, the drainage hose/pump may be clogged and needs to be cleaned. If not, your appliance may possibly be experiencing an issue with the door lock assembly, faulty pump, timer or control board not communicating correctly. In this case, because it could be a number of any one of several underlying causes, I would recommend contacting a professional to properly diagnose and repair your washer. Best!

The belt might be out of alignment or broken.

Hello friend, thank you for your post!

I see you are asking for help with a door sensor for your Frigidaire washer. What exactly are you asking for in regards to the door sensor? I would need some additional information in order to provide you accurate assistance. I look forward to helping you. -Matt