Top 20 Symphonic WF20D4 TV Questions & Answers

0392 0459 0510. Check these codes. If you wish to get more details; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. Common set-up codes to check with TVs and other devices are given, in the order of the "device's brand name" in alphabetical order. Pull up older posts. Surf the site with patience. Surf the sites by type in the brand name to your set, in its search box.

Symphonic WF20D4... | 71 views | 1 helpful votes

You should troubleshoot from its main power regulator section circuit. It will be best to contact any service technician.

Symphonic WF20D4... | 27 views | 0 helpful votes

There should be around 105VDC at the supply end. For more details, refer the repair manual.

Symphonic WF20D4... | 34 views | 1 helpful votes

As there is no 'Menu'button on the front panel of this TV, to select other inputs, you must have a remote control.

Symphonic WF20D4... | 336 views | 0 helpful votes

These are the universal remote control codes for Philips. 0062 0204 0184 0208 0205 0206 0207 0004 0189 0183 0199 0200 0288 0456 0003 0008 0068 0075 0086 0087 0141

Symphonic WF20D4... | 31 views | 0 helpful votes

Use the remote dishnet to automatically detect your code for the tv. Most of the time the procedure is on the remote.

Symphonic WF20D4... | 342 views | 0 helpful votes

Try these codes.
0053 0189 0227 0456 0024

Symphonic WF20D4... | 85 views | 0 helpful votes

Check the remote with new batteries. If it do not work, remote control has the trouble. You can't switch the set ON by its front panel power switch, as it has been shut down by remote command.

Symphonic WF20D4... | 56 views | 0 helpful votes

Hi, my name is Cheri Torres and I work on the DISH Internet Response Team. I came across your post recently and would like to help. We have a few different codes for each of our different models of remotes. I will list here for you the best codes for each of our different models or remotes and, the instructions for addressing your remote to your TV. I hope you find this information useful and if you have any further questions or concerns feel free to ask.

Remote models Remote codes
3.0, 3.1, 3.2, 3.4 IR remotes - codes 569, 632, 733, 694, 569, 846.
5.0, 5.2, 5.3, 5.4 IR remotes - codes 632, 522, 624, 846.
4.0 and 4.4 IR/UHF remotes - codes 632, 569, 733, 694.
6.0, 6.2, 6.3, 6.4 IR/UHF remotes - codes 733, 632, 694, 756. 569.
20.0, 20.1 IR and 21.0 21.1 IR/UHF remotes - codes 632, 733, 756, 846, 679, 694.

Instructions for addressing the remote to the TV
1. Press and hold down the TV button until all the lights on the remote are lit.
2. Enter the 3 digit code for your remote.
3. Press the pound(#) button once.
4. Test the functionality of your TV.

Cheri Torres
Internet Response Team

Symphonic WF20D4... | 196 views | 0 helpful votes

Just buy one "ATLAS METROCAST -OCAP 5 DEVICE" universal remote control. Symphonic TV is listed with its codes. Codes are:
0180, 0171, 1944
Setup proceedings can be had with its catelogue. OK

Symphonic WF20D4... | 184 views | 0 helpful votes

This set doesn't have a headphone jack, nor does it have RCA audio output jacks. Without one or the other, you're out of luck connecting headphones to this TV.

I remember a product some years ago that allowed adding headphones using a small microphone placed in front of the speaker. This was hooked to a little amplifier that ran the headphones so the volume could be independently controlled. It was marketed as a way to let "hearing-impaired" family members listen to TV shows without needing to make it uncomfortably loud for others. I haven't looked, but something similar might still be available. It's cumbersome, though, and needs power, plus maybe being costly if you find one.

It's possible to add a headphone jack, but you need to know how to do electronic soldering. Find a spot on the case where you can make a hole and mount a headphone jack, then wire it to the speakers. If you want the headphones to cut off the speakers when plugged in, you need a switching jack, and the speaker wires need to be cut and connected to the correct terminals. The switch built into the jack then disconnects the speakers when the headphone plug is in. If you don't need to turn off the speakers it's a little easier. You just need to wire from the jack to the speaker terminals. I've added jacks on quite a few sets. If you don't feel up to it and don't know anyone who is, you can see if a TV shop (if there are any left in your area!) would do it. (The shop I used to work for charged about $20, including the jack, but that was over 10 years ago now.)

Good luck, and thanks for using Fixya!

Symphonic WF20D4... | 225 views | 1 helpful votes

Hello, you may have already gotten this information, but here are some simple steps to get that remote working for your tv. The link below will walk you through a power scan, where you can scan the tv to get the correct code for the DISH remote to your tv.

and also, here is a link to the codes for the tvs. I hope this helps!!

Becki Barned
DISH Network Customer Service

Symphonic WF20D4... | 282 views | 0 helpful votes

call 1-800-242-7158 and order another remote. Remote number is Item #NE228UD

Instrucdiones En Espanol

Or, go to your local Superstore (walmart) and purchase a universal remote.

Symphonic WF20D4... | 83 views | 0 helpful votes

try this,press manual buttons on tele as if you are changing tv chans ,if you do this thru all mem chans on tele you should come to one that changes to video input this has worked for me on other televisions.

Symphonic WF20D4... | 607 views | 0 helpful votes

i have a small universal remote and need the codes fir the tv

Symphonic WF20D4... | 126 views | 0 helpful votes

You are correct if your TV doesn't have audio output you can buy an adapter at radioshack or online probably 1/8 to RCA like this one here

I’m happy to help further over the phone at

Symphonic WF20D4... | 174 views | 0 helpful votes

Try this method:
Turn on the device you want to program.
Press and hold CODE SEARCH until the indicator light lights then release code search.
Press and release the device button you are programing TV, the indicator light will blink once then remain lit.
Press and release OFF/ON until your device turn off.
you may have to press upto 200 times
When your device turn off press enter button the indicator light will go off,good luck.

Symphonic WF20D4... | 1,109 views | 2 helpful votes

Yes you may hook that up to the coaxle end of this unit or the RCA scart connection on the back.

The coaxle end you would need to be on channel 3 or 4 make sure you verify witch channel you vcr is under. Thanks

Btw, I’m available to help over the phone in case u need at

Symphonic WF20D4... | 98 views | 1 helpful votes

Not finding what you are looking for?
Symphonic WF20D4 TV Logo

62 questions posted

Ask a Question

Usually answered in minutes!

Top Symphonic Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76237 Answers

Cindy Wells

Level 3 Expert

6073 Answers

matt martin
matt martin

Level 3 Expert

1257 Answers

Are you a Symphonic Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Symphonic Televison & Video

  • Symphonic Televison & Video

Most Popular Question

remote programming codes

  • Televison & Video