20 Most Recent Xerox WorkCentre M-24 Color Copier - Page 8 Questions & Answers

Well, since the drum is a consumable, most of the copies is running life span counter. When the drum reached the life span, the message will pop out. Well, if the print out still ok, just ignore it.

It's possible, transfer paper can melt to the fuser roller, the drum, and other rollers in the printer and leave them sticky and unusable. Problems can manifest right away, if the plastic crud left behind is think. Or they can manifest several days later as toner turns the clear melted plastic black.

If several days later your still running, you're probably safe.

The tab for the interlock actuator either broke off or the interlock switch itself has come out of position.

You need the extra 256K memory board to make this work. It's standard memroy if I recall.

No , the machine does not support scan to E-mail.

On your finisher, the stacker tray, The tray that moves up and down to stack the papers, has not detected the paper being taken out of the tray. There is a sensor that has a black actuator sticking out in the middle of the output tray, It either fell off or is stuck.

In one of these diagnostic areas you will find an auto gradation adjustment, perform that. Here are the steps.
To enter the CE mode:

1. Press and hold the 0 key for 5 seconds, then while still holding down the 0 key, press the Start button.
   The CE Access Number screen will appear.
   
2. Enter 6789 and press Confirm.
   
3. The top most area of the UI display will be reversed to let the user know that the mode has changed to the CE mode
   

1. Enter the Diagnostic mode.
   
2. From the Common Settings screen, select Image Quality Adjustment.
   
3. Select Calibration.
   
4. Select the button of the Screen Type to be calibrated, that is, Copy Job - Text, Copy Job - Photo, Print Job - Text, or Print Job - Photo.
   
5. Press the Target button and then select the type of jobs to be calibrated, that is, Copy & Print Jobs, Copy Jobs Only, or Print Jobs Only.
   
6. WC 72XX only: Load A4 paper in the Tray 5 (Bypass). Press Save.
   WC73XX only: Select a paper size and type using the paper supply button
   
7. Press Start. The auto gradation routine will run and a message will display upon completion.
   
8. Take the print from the output tray. Follow the instructions on the screen to complete the color correction.
   

Start with this

1. Make sure to set the Print Quality mode in the print driver to "Standard" and the TekColor Correction to "None" before performing the next step. This will allow the job to purge only the problem color. Other settings may cause the printer to use a percentage of the other ink sticks.
   
   
2. Print approximately 50 - 100 pages of the document, as necessary, until the printed color returns to normal.

Next. This is on xerox.com downloads and drivers.

The updated sRGB Display and sRGB Vivid color tables for the WorkCentre will help with the following issues that have been found with the original factory color tables.

• RGB images contain too much yellow.
• RGB image red shades are too orange or too light.
• RGB object blues are too dark or aqua.
• CMYK objects use the sRGB Display color table when the Automatic TekColor correction is used. After the updated color tables have been downloaded to the WorkCentre, the CMYK objects will use the Commercial Press TekColor correction when Automatic is used as the TekColor correction.
  
  NOTE: The new color tables will only take affect when using the Enhanced or High Resolution / Photo print quality mode.

To update the RGB color tables:

1. Click on the [Drivers & Downloads] link under the Product Resources menu on this window to download the updated color tables to a known location on the computer's hard drive. The color table update file is located under the Color Profiles section on the Drivers and Downloads page.
2. After the file has been downloaded to the computer, send the file to the WorkCentre. See the Related Items below for additional information.

J1 mean any paper jam in paper feed area or sensor displace.lower cassate or multi pass tray.clear jam paper then solve your problem.

check the adjustment guides of the paper tray.

Esta problema debe estar en la caletador, o el "fuser".
Si peude cambiar la Thermister, la cosa que cala la temutura, esa cosa puede leller la tempatura mala. Cambia la.

Si el papel se para antes que se sale, checa las manitas en el switches. Se callen o se torra y no bajan. Debem esta fojas todo tiempo.
Ojala que esta ajuda trabaja.

check the pressure of the fuser adjustment

check your dev tanks /check developer

this is a fuser related problem . check for fuser contamination

hi, open the front door, release the drum latch,open the metallic plate next to the front door then remove the waste toner bottle

Enter in the machine menu and select the machine status mode.

Wash out the bottle with warm soapy water.

You it is necessary to return the code of the manager, or apply to service centre, such information to you nobody will not give and no such code, which you have found in internet. This problem to me known. This only service centre, they do not divulge such information

http://www.xrxgsn.com/admin/public/2990/m24consumableext.html