20 Most Recent
Xerox WorkCentre M-24 Color Copier - Page 5 Questions & Answers
Hi, I have Xerox Wc M24.The Machine has Magenta
There is a complete set up to do color registration.
it is a 4 step process. It's DC 685. E-mail me at
[email protected].
I can send you more info that way.
-
Belt Edge Learn - to align the Transfer Belt positioning system.
-
Fine Skew Setup - automatically performs horizontal and vertical alignment, and reports any skew in the various images caused by ROS misalignment. This skew must be corrected through manual adjustment
-
IN/OUT Setup - automatically performs magnification adjustment so that scan lines are the same length for all four colors. Also checks for skew.
-
Center Setup - Aligns the midpoints of scan lines for all colors, for magnification balance
WorkCentre M24 is ticking me
You have a bad fuser fan. Xerox part number 127K29340. Located on the back of the machine. Very common problem. Look up on google a business called the parts drop.
They will have it.
Describe 102-372 code problem in m24 xerox work
Solution : Power OFF the Printer, Wait 45 Seconds, Then Power ON
CAUTION: If the machine is powered OFF / powered ON, all information that is stored in the machine's memory may be erased.
NOTE: Before powering OFF, make sure that all copy or print jobs have completely finished. Never power OFF in the following instances:
- While data is being received.
- While jobs are being printed.
- While jobs are being copied.
- While a scan is being executed.
- Power OFF the machine. The power switch is located on the front right side of the machine under the Control Panel.
NOTE: Before the machine is powered ON again make sure the Touch Screen is blank.
- Power ON the machine.
NOTE: When the power is ON, a 'Please wait...' message will be displayed. This message indicates that the machine is warming up and cannot be used. After 45 seconds, the machine becomes ready for use.
If the issue is not resolved repeat steps 1 and 2 a second time.
Cyan and majenta tone is not good
Solution : Perform an Automatic Gradation Adjustment (Color Calibration)
Automatic Gradation Adjustment compensates for tones when the color tones shift in color copies / prints. Compensating for color tones maintains the quality of color copies / prints made by the machine at a fixed level.
NOTE: Output of the Automatic Gradation Adjustment chart is added to the metered copy count.
NOTE: When Gradation Adjustment is selected, the following changes will be made to default copy settings set in System Settings mode:
- Copy Density = Normal or Auto
- Color Shift =Normal
- Saturation = Normal
- Color Balance = 0
- Sharpness = 0
- Press the [Access] button (key symbol) on the Control Panel. The Access button is located above the number "3" on the numeric keypad.
- Using the numeric keypad, enter your administrator password and select [Confirm] on the Touch Screen. The System Administration Menu screen will be displayed.
NOTE: If you do not know the password, contact your administrator. The initial password at machine install is 11111. If the administrator encounters a problem with changing the password, or forgets the password, a service call must be placed.
- Select [System Settings]. The System Settings screen will be displayed.
- Select [System Settings] again.
- Select [Common Settings].
- Select [Image Quality]. The Image Quality Adjustment screen displays.
- Select [Automatic Gradation Adjustment].
- Load 8.5 x 11 inch (216 mm x 279 mm) or A4 (210 mm x 297 mm / 8.3 x 11.7 inch) paper in Tray 5 (Bypass Tray). Adjust the paper tray edge guide so that the guide gently touches the edge of the paper stack.
- Select the desired gradation adjustment screen.
- Press [Start]. The Adjustment Chart is output.
NOTE: When printing the color chart for Auto Gradation and you get the message,'Auto Graduation Procedure has completed with an error' make sure that 8.5 x 11 inch (216 mm x 279 mm) paper is loaded into Tray 5 Long Edge Feed (LEF).
- Place the Adjustment Chart face-down on the Document Glass with both the Magenta color patches against the left side of the glass.
- Place 5 sheets of white paper on top of the Adjustment Chart and close the Document Glass Cover.
- Press [Start].
- To continue Automatic Gradation Adjustment with other screens, repeat steps 6 to 10. When you are finished, select [Close] until the System Settings screen is displayed.
- Select [Exit] to exit the System Settings mode.
Hope it helps!
Not finding what you are looking for?