Mitsubishi Diamond WD-65831 65" Projection HDTV - Page 7 - Answered Questions & Fixed issues

Might be tuned to the wrong output. The big tv has more than one input and is select able. Is there a blue ray selection for TV or input for that device.

It is helpful to have the sequence of the blinking red light. This may help:MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927Page 433. Error Code Operational CheckNote: The TV must be in "Shut Down" and not have been switched Off, to perform the Error Code OperationalCheck. When the TV is switched Off, the code automatically resets to "12" No Error.Pressing the front panel "DEVICE" and "MENU" buttons at the same time, and holding for 5 seconds,activates the Error Code Mode. The LED flashes denoting a two digit Error Code, or indicating no problemhas occured since the last Initalization.Note: The front panel buttons must be used, NOT those on the Remote Control.• The number of flashes indicates the value of the MSD (tens digit) of the Error Code.• The flashing then pauses for approximately 1/2 second.• The LED then flashes indicating the value of the LSD (ones digit) of the Error Code.• The Error Code is repeated a total of 5 times.Example: If the Error Code is "23", the LED will flash two times, pause, and then flash three times.4. Error CodesThe Error Code designations indicating malfunction, or no malfunction, are listed below:POWERLEDSTATUSLEDLAMPLEDPowerStatus ConditionOff Yellow Off LowPower Excess heat. Check Lamp FilterOff or On Off Yellow Nochange120w usage time over 7000 Hrs.150W usage time over 3500 Hrs.Off Off BlinksYellowLowPower Lamp Cover openOff BlinksYellow Off " Filter Cover OpenOff Off Red Stby Lamp did not turn OnOff BlinksRed Off LowPower Fan StoppedOff Red Off " Circuit failure (short or DVIconnector unplugged)Abnormal LED IndicationsError Codes "DEVICE" & "MENU"Error Codes Description12 No error detected22 Recovery from Reset32 Lamp cover is Open34 Lamp abnormality35 DM Fan failed (Chassis Fan)36 Exhaust or Lamp Ballast Fan failed37 DMD Engine Fan failed38 Lamp temperature abnormally high. Remove Lamp to check filter.39 DMD temperature abnormally high41 Short is detected (Standby Power Supplies)42 Lamp Fan failed44 DVI cable between Format and Engine disconnected46 DMD Temp. Sensor not detected (check DT connector))47 DM Temperature too high48 Engine power supply short detected51 Speaker Drive circuit short detected52 HDD excess temperature (V30+ & V31 only)55 HDD Fan Stopped (V30+ & V31 onlyt)

Part#: KIT-MIR 767D084020 try this web site: https://www.encompassparts.com/item/7615765/Mitsubishi/KIT-MIR_767D084020/Kit-mirror_767D084020 or http://mitsubishi-tv.com/support

Try a new lamp. You will need the model# to locate the proper part# for your unit.

Hello: From the sound of your description of your problem you likely have a defective lamp. Feel free to give us a call at 866-764-5822 and we would be happy to help you troubleshoot the problem over the telephone. Best Regards Dan DLP Lamps Projector Lamps Specialty Lighting

Condensor? or just the projection lens. Condensor is just a lens like pice of glass used you distribute the light of the lamp evenly.

When you replaced the lamp did you reinstall the cover correctly? There is a safety switch incorporated in the cover .

major circuit problem, time for a flatscreen

Go into menu and reset "lamp timer".

If you used a generic or neolux lamp--this could happen, Mits do NOT like them. use a Phillips bulb !!

Have you been turning off this set from some OTHER power source, such as a cable box ? The set MUST have constant power for at least 3 minutes after turn off for the bulb to cool down. Also, do NOT use a generic "bargain bulb" to replace--either an original or a phillips one do NOT use an Osram "neolux" lamp, Mits. do NOT like them !!

Are you sure the message is coming from the TV or could it be comming from a component you have connected to the TV?

Possible heat issue. Check for fan operation and any dust build up.

I happened the same problem and the solution must change the power pack

Make sure your "video" cord is plugged in properly.

Dear Reece, It seems that you have a problem with the power supply circuit that powers the video part of your projection TV or the power drivers for the three color (RGB) tubes. You will need to have it repaired by a service technician. Hope it helps! Best regards, Miguel Luiz Martins

Video board problem. Find honest TV tech.

it just put like colors on it like red ,green , black ,white

REPLACED SENSOR P# 299P313010A LOCATED BEHIND THE LAMP. TO REPLACE IT, NEED TO REMOVE THE LAMP AND DO IT THROUGH THE LAMP OPENING WITH SMALL PHILLIPS SCREW DRIVER...this can fail causes intermittent shutdown and/or symptom you describe...........good success, meder's tv service

turn the tv off. remove the lamp. blow out the terminals. then replace it. Had the same issue on mine.This solved it.