20 Most Recent Mitsubishi Diamond WD-65831 65" Projection HDTV - Page 8 Questions & Answers

in repair shop

Mitsubishi WD... | Answered on Jul 11, 2015

Fault to the main power supply regulator board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts.

Mitsubishi WD... | Answered on Jun 14, 2015

Probably a bad lamp. what is the model?

Mitsubishi WD... | Answered on Jun 03, 2015

Your tv needs a dm power board repair,this little board is located inside the metal box where digital antenna plugs in.
you'll need to remove this little board and send it to us for repair,we are on ebay,look for texas tv parts.
also you can just search at ebay's search bar for this repair by typing this #:330700000004.

you can also visit our new born store :www.texastvparts.com
thanks a lot!!!

Mitsubishi WD... | Answered on May 09, 2015

unplug it, wait 1 minute & plug back in to see it it will reset.If not you will need a technician.

Mitsubishi WD... | Answered on Apr 29, 2015

Hi Jenell

Looks like you might have lost one of your primary colours. RGB
A section of the internal electronics controls Red Green Blue.
Check for loose plugged in cables on back. Antenna or Cable
Try inputing a signal from another external video device like a hard drive.
Try a couple of hard slaps on the back to see if it changes.
If it does then you may simply have an internal bad connector or loose wire.
Make sure the air holes around the unit are clean to allow cooling air to flow.
Other than that, you will need a technician to open it up.

Mitsubishi WD... | Answered on Apr 02, 2015

I'd guess the cooling fan is not working and the high temp cutout shuts it off.

Mitsubishi WD... | Answered on Mar 26, 2015

hello there. It's a bit of a strange question to ask. But I would first check the lamp umber printed on the lamp. I am sure there is a printed number on it. Secondly I would return the lamp to a TV retailer and purchase or order a new lamp. But if this is too much for you, you can get a lamp from the internet at possibly half the price, delivered, on Amazon and EBay. Here are a few links to try. Hope it's not too much for you but it's worth a try. Cheers.
http://www.youtube.com/watch?v=_ONPuB5L-x4 http://www.nextag.com/mitsubishi-tv-lamp-replacement/products-html http://www.mitsubishi-tv.com/support/faqs

Mitsubishi WD... | Answered on Mar 08, 2015


Mitsubishi WD... | Answered on Mar 03, 2015

bulbs explode when they are not cooled properly. check your fans.

Mitsubishi WD... | Answered on Mar 02, 2015

Your color is distorted because your color wheel is probably going bad. Try resetting all the picture values first. Sometimes they need to go back to normal when the lamp is changed. Lamps only provide white light and have no bearing on colors unless they are very dim. Also check your cables. a loose or bad cable can cause this as well. Lastly make sure your new lamp is made by Osram or Philips. knock offs wont work.

Mitsubishi WD... | Answered on Mar 02, 2015

You have a bad power supply board. Check EBay or Shopjimmy to find a new board. You will need your model #. Which starts with WD-

Mitsubishi WD... | Answered on Mar 02, 2015

Are you sure the TV supports 720p? Many older 55" RPTVs are 480 only. Even with Component. Most older component is only 480

Mitsubishi WD... | Answered on Mar 02, 2015

Youre lamp has failed. you need a new lamp.http://projectorlamps.com/mitsubishi-dlp-tv-bulbs-915b441001-pvip.html 915B441001 PVIP Mitsubishi DLP TV Bulbs

Mitsubishi WD... | Answered on Mar 02, 2015

You must use the factory remote. Mutlibrand will not work for this option. No matter the universal remote, you need the original. No other way to do this.

1. Press MENU on original remote only
2. Then press 2,4,7, and 0
3. Select "initialize" and then 'ENTer"

This will full restore to factory original settings. but you need the original Mitsubishi remote.

Mitsubishi WD... | Answered on Mar 02, 2015

Hello, did you touch the face of the lamp? If you did, you will need to clean it off to remove your prints. The next thing is, the fans may not be working properly and not cooling the lamp and light engine properly. Let me know....tks

Mitsubishi WD... | Answered on Feb 25, 2015

Not finding what you are looking for?
Mitsubishi Diamond WD-65831 65" Projection HDTV Logo

100 questions posted

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1257 Answers

The Knight
The Knight

Level 3 Expert

76204 Answers


Level 3 Expert

13434 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

WD Mitsubishi

  • WD Mitsubishi

Most Popular Question

wd 65831 mitsubishi tv

  • Televison & Video