Top 20 Belkin (F5D8231-4) Wireless Router (F5D82314) Questions & Answers

Belkin wireless 'N' with Vonage router and cable ISP modem...

Hi, since your Internet source is the ISP modem, you have to connect the cable from it to the yellow connector of Belkin router, then you can connect the VoIP router and computer to any of the ports (connectors) labeled 1-4 , remember to restart clients (PC & VoIP router) to get the new IP from Belkin router.

Belkin... | 236 views | 0 helpful votes

1 Answer

I have a Belkin F5D 8631-4 ADSL2+ wireless modem router which becasue of power cut recently stopped working. I cannot get any lights to stay on, but when I plug in, I can see the blue light (middle) a

once you press RESET you will not be able to connect wirelessly, you have to configure the router. you can only do that via a LAN cable connected PC. switch router off for at least 10 seconds. attach a pc using a lan cable to ports 1/2/3/4 NOT to the WAN port(5). switch on the router and start your browser. type in either http://router or 192.168.2.1 to get router menu up. configure the router because you have RESET it. http://www.belkin.com/uk/support-article?articleNum=8181

Belkin... | 84 views | 0 helpful votes

1 Answer

How do I know if it needs any firmware upgrades. The router is not working with Netflix.

Do you have some kind of hardware attached to your router from Netflix? My understanding Netflix is Internet base and can be use by a multiple devices like PS3 $4 WII Xbox I believe and some of the DVD players which is direct ether net port or via wireless connection. Unless your router is asking for a static IP and do the port forwarding... let me Iif this one help

Belkin... | 95 views | 1 helpful votes

1 Answer

Where is the wps button on a N 1 Belkin route?

Using Wi-Fi Protected Setup
WPS uses WPA2 (described below) for encryption. It does not
provide additional security, but rather, standardizes the method for
securing your wireless network. You may use either the Push Button
Configuration (PBC) method or PIN method to allow a device access to your wireless network. Conceptually, the two methods work as follows:
PBC: Push and hold the WPS button located on the back of your
Router for three seconds. Then initiate the WPS procedure on the client device within two minutes. Refer to your client's documentation on this procedure. Pushing the PBC button will automatically enable WPS. The client has now been securely added to your wireless network.
PIN: The client device has a PIN number (either four or eight digits)
that is associated with WPS. Enable WPS through the GUI shown
below. Enter the client's PIN into the Router's internal registrar
(accessed through this GUI). The client will be automatically enrolled
into your wireless network within two minutes.

Belkin... | 242 views | 0 helpful votes

1 Answer

PC will not go wireless

If your PC is a desktop, not a laptop, probably it can be hooked to your modem/router only wired (using an Ethernet cable). If, for whatever reason(s), you want to connect it wirelessly, you have to buy a USB wireless adapter.

Belkin... | 48 views | 0 helpful votes

1 Answer

Why i do not have any sound on my phone

Prob with Router or Phone? (Takes time to try to understand/figure out your issue. Please explain Details.) Best answer I have so far is Your Cell-Phone Provider does NOT allow your Phone to do Internet calls over a WiFi connection thru the internet unless You pay for it. Didn't used to be that way, had the prob with T-Mobile myself. Was free for a bit, then T-Mobile started charging me or turned off the feature. SUCKED! Most likely, your Cell-Phone Provider because they want those minutes charged to your account. Sorry bout that. Thanks.

Belkin... | 32 views | 0 helpful votes

1 Answer

My phone line is going from my phone to the router but there is no dail tone

Who is the phone service provider? What is the IP, subnet and gateway address of the phone? and what are they supposed to be? Common problem is the gateway is a different number. Thats all I can say without more information.

Belkin... | 20 views | 0 helpful votes

1 Answer

Connecting Seagate Backup Plus Desktop drive (STCA3000101) to Belkin N750 wireless router.

Usually you don't need to setup any additional settings or creating new users on the Belkin router to access an USB HDD attached to it, if you used the Belkin Router Manager to set it up.

The Seagate drive you are using have it's own power supply, so that should not be a problem. Also the accepted formats are FAT16, FAT32 and NTFS formatted HDD.

You can try to set it up again using the manager. This is the user manual for your router, if it helps:
http://www.belkin.com/networking/manual/MAN_F9K1103_8820-00778_RevA01_N750.pdf

If you still can't get it working, let me know and we will try to find another solution.

Belkin... | 105 views | 0 helpful votes

1 Answer

N150 password

Check the bottom there should be a Password written down or normally blank or admin admin

Belkin... | 23 views | 0 helpful votes

pdf Manual

(F5D8231-4) Wireless Router (F5D82314) Manual

Belkin (F5D8231-4) Wireless Router... | Uploaded on Sep 02, 2013

1 Answer

I have a belkin router and my computer crashed but it is now fixed but the router says its connected but can't excess the internet

Pull the power from the router and modem. Wait about 1 minute and plug in just the modem. Wait 1 minute for the modem to come up completely and plug in the router. Wait another minute for the router to come up completely. Now test your connection.

Belkin... | 67 views | 0 helpful votes

1 Answer

I have a Belkin.3AED won't go wireless

Perhaps this will help: http://cache-www.belkin.com/support/dl/p75170-d_f5d8231-4_man.pdf

Belkin... | 26 views | 0 helpful votes

1 Answer

I want to make a password

You can create password from 'wireless' option in router setup page. Here you can type your own password.Read more

Belkin... | 37 views | 0 helpful votes

1 Answer

How to CONNECT a Belkin MODEL F5D9231- 4 V1 Wireless Router with CenturyLink 660 Series DSL Modem

Go to http://www.ehow.com/how_4527815_two-routers-one-home-network.html

Belkin... | 232 views | 0 helpful votes

2 Answers

There is no Internet between the hours 8:00pm and 11:00pm

Wi-Fi routers usually have the ability for the user to restrict the hours of Internet access(most of the time used for unruly teenagers).Log into the router(the IP address might be 192.168.1.1,if not it is probably on the router somewhere).Then locate "admininstration" or something like that to look at the access time settings.

Belkin... | 43 views | 0 helpful votes

1 Answer

Hmm

Reset your router back to it's factory settings by holding the reset button for about 5 seconds. I have provided a list of the most popular router brands. If it does not work you may need to google what your specific model's default IP address/default username/default passwords are, for example search for "Encore ENHWI-2AN3 default IP address" The default login info can change, it can depend on where you obtained your router. If you purchased it yourself from a store then the standard defaults should work. If you obtained your router from your Internet Provider you may need to contact your service provider. It also may depend whether it's an old or new model router as well. And you may need to press and hold the reset button on your router several times before it actually clears. Make sure you have a wired connection then once you have accessed your router simply run the Setup Wizard. Set your SSID as something you'll remember like "Mavericks Network" and your Password can be something like your phone number for example 3109876543

Belkin - Username: Leave the field blank Password: Leave the field blank Default IP address is: 192.168.2.1

Buffalo - Username: root Password: Leave the field blank Default IP address is: 192.168.11.1

D-Link - Username: admin Password: Leave the field blank Default IP address is: 192.168.0.1

Encore - Username: admin Password: admin Default IP address 192.168.1.1

Linksys - Username: admin Password: admin Default IP address 192.168.1.1

NetGear - Username: admin Password: password Default IP address will be: 192.168.0.1 or 192.168.1.1

TP-Link - Username: admin Password: admin Default IP address 192.168.1.1

TrendNet - Username: admin Password: admin Default IP address 192.168.10.1

Zhone - Username: admin Password: admin Default IP address 192.168.1.1

Zyxel - Username: admin Password: 1234 Default IP address 192.168.10.1

Belkin... | 1,000 views | 0 helpful votes

2 Answers

I have lost the security

Hi!

If you don't remeber the wireless security code, maybe you still remeber the user and password to access the web management interface of the router.
Then you have to connect the laptop to the router by using a network cable. Open a browser window, type in the IP adress of your router and check the wireless setup section. There you can find / modify the wifi security code.

If you don't know the router's IP adress, then open on your computer a ms-dos prompt and type the command
ipconfig /all

it will display your current IP adress, subnet mask and GATEWAY. The gateway adress is the router's IP adress that must be typed into the browser.

If you don't remember the user and password for accessing the router's web interface, please refer to the router's user manual in order to reset it to factory default configuration, and then proceed as for the first installation of the router.

Hope it helped,

Bogdan

Belkin... | 339 views | 0 helpful votes

2 Answers

Play Wireless Router F7D4302v1 I'm trying

I've had this same issue with a different router and my Xbox 360. You're going to want to find the "DMZ" section of your router and put your console/pc's IP address in that section.
I believe you can do it by logging into your router, selecting "Advanced Setup",then going to "Firewall", then "DMZ". To find your console/pc's IP address, look for a list of all the devices on your network. There should be a "Summary" page or something similar within your router. Take that IP address and put it in the DMZ field.
The idea is to put your console/pc in a special place in the router [the "Gaming DMZ (de-militarized zone)] that it doesn't receive interference, but your router needs to know what device to do that to.
Let me know if you have any further questions!

Belkin... | 94 views | 0 helpful votes

1 Answer

Hi, I would really appreciate it if someone could

hi, go to the belkin website, you should get it there but you may need to contact them

Belkin... | 24 views | 0 helpful votes

1 Answer

When i turn the belkin

Thank you for using FixYa
Red or amber lights tells you that something is wrong with the modem, but it could be just the configuration. Be sure you have an internet signal on the line coming into the modem and that the connections are all plugged into the modem/router correctly. Most probable, is that you need to enter the user name and password. Here is a link for the manual for your modem, so you can download it and see for yourself. There are procedures that we need to go through with you at the computer but the first thing is establishing the internet signal. Your Internet provider and help you and send tests to the router from their central office. The phone line could be a problem, the internet signal could be bad and last but not least is the router. We can only see one question at a time that you post, so I suggest you contact your ISP.

http://en-us-support.belkin.com/app/answers/detail/a_id/128

Hope this was useful and please comment if this was helpful to you.

Belkin... | 58 views | 0 helpful votes