20 Most Recent Pioneer CDJ-800MK2 Turntable - Page 5 Questions & Answers

To program your Sanyo GXDB remote to work with your Pioneer Elite VSX 33 receiver, you can try the following steps:

1. Turn on the Pioneer Elite VSX 33 receiver manually using the power button located on the receiver itself.
2. Hold down the "Code Search" button on your Sanyo GXDB remote until the LED light on the remote stays lit or blinks.
3. Press the "TV" or "DVD" button on the remote, depending on which device mode you want to program the receiver to.
4. Enter the corresponding code for Pioneer receivers. You can find a list of Pioneer remote control codes in the instruction manual that came with your Sanyo GXDB remote or by searching online. Enter the code using the number buttons on the remote.
5. Point the remote at the Pioneer receiver and press the "Power" button. If the receiver turns off, it means the remote has been successfully programmed. If not, repeat the process using a different code from the list until you find the one that works.
6. Once the remote successfully turns off the receiver, press the "Code Search" button again to save the code. The LED light on the remote should turn off or stop blinking.
7. Test the remote by pressing other buttons, such as volume up/down or channel up/down, to ensure it is functioning properly with your Pioneer Elite VSX 33 receiver.

If you're still having trouble programming the remote, consult the instruction manual that came with the Sanyo GXDB remote or contact Sanyo customer support for further assistance.

I am assuming the receiver is new. In this regard, if the Pioneer VSX-902 receiver is turning on but you're not seeing any display, here are some troubleshooting steps you can try:

1. Check the video connections: Ensure that the HDMI, component, or other video cables are securely connected between the receiver and your display device (such as a TV or projector). Make sure the cables are inserted properly and that they are in good condition. Try disconnecting and reconnecting the cables to ensure a secure connection.
2. Verify the input and output settings: Check that the receiver's input source is correctly selected. Use the remote control or front panel buttons to cycle through the different input options until you find the one connected to your video source. Additionally, confirm that the output settings of the receiver are properly configured to match your display device.
3. Check the display settings: Some receivers have options for adjusting the display settings, such as brightness, contrast, or resolution. Check the receiver's on-screen menu (if available) or refer to the user manual to access the display settings and make sure they are properly configured.
4. Perform a factory reset: Try performing a factory reset on your Pioneer VSX-902 receiver. This can often resolve any software-related issues that may be affecting the display. Refer to the user manual for instructions on how to perform a factory reset specific to your model.
5. Test with a different display device: If possible, try connecting your receiver to a different display device (such as a different TV or monitor) to determine if the issue lies with the receiver or the original display. This can help narrow down the problem and identify if it's related to the receiver or the specific connection or settings with the original display.

If none of the above steps resolve the issue, it's recommended to contact Pioneer customer support or consult a professional technician for further assistance.

To perform a hard reset on a Pioneer CDJ-400, follow these steps: 1. Turn off the CDJ-400 by pressing the power button located on the front of the unit. 2. While holding down the Eject button (located on the top left of the CDJ-400), turn on the power switch. 3. Continue holding the Eject button until the display shows "PIONEER CDJ-400." 4. Release the Eject button. 5. Press and hold the Track Search Forward (">>") button and the Track Search Backward ("<<") button simultaneously. 6. Keep holding these buttons until the message "Resetting All Data" appears on the display. 7. Release the Track Search buttons. 8. The CDJ-400 will perform the hard reset and return to its factory default settings. This process may take a few moments. 9. Once the reset is complete, the CDJ-400 will restart. Please note that performing a hard reset will erase any custom settings or saved data on the CDJ-400. Use this option with caution and make sure to back up any important data before proceeding.

Try an known good CD that works in other CD players

Question edited for clarity and correct order, 'make model (what it is)' plus spelling of 'dual'. There are two prospects here including a place that makes custom belts'. The RX-541 may fit. https://www.google.com/search?q=Pioneer+RX+590+Dual+Cassette+Deck+belt+kit ..

Generally speaking, an amp protects itself from heat, shorts, overloads and operator exuberance by refusing to turn on or stay on.

Overloads can be from excessive periods of high output or marginally low impedance loading by the speakers; and shorts would be wiring issues or a speaker blowing up.

You should be able to feel if it's hot. WHY is it overheating? Make sure it has sufficient ventilation on all sides and that vent holes are not blocked by dust balls. Ensure the fan (if equipped) is running as designed (some only operate on demand). Clean dust and debris from it.

If the amp comes back on after cooling, you're lucky. They only have so many self-protection cycles in their lives so continuously resetting or cycling their power without addressing the cause can do more harm than good.

If it protects immediately on a cool power up you should disconnect the speaker connections and try it 'naked'. If it comes up then diagnose which lead(s) are shorted. If it does not come up the problem is internal and should be left to an experienced and competent hands-on tech.

Check for loose speaker connections at the speaker as a root cause for intermittent shutdown.

The service manual is available for free after you register here...

http://www.hifiengine.com/manuals/pioneer/m-l11.shtml

Question edited for clarity and typos. The first link has reset information. It would also remove the case and vacuum out any dust. Also see if there is a cooling fan in there anywhere. https://www.google.com/search?q=Pioneer+Elite+VSX+503+it+went+into+%27Protect+Mode%27 ..

To perform a reset on your Pioneer VSX-S520 using the remote controller, follow these steps:

1. Make sure the receiver is turned off.
2. Press and hold the "BAND" button and the "STANDBY/ON" button simultaneously until the display starts flashing.
3. Release the buttons and the display should stop flashing.
4. The receiver is now reset to its default settings.

If the "Fl off" blinking red light persists, it could indicate a problem with the receiver that requires further troubleshooting or repair.

If your Pioneer PL 640 turntable is experiencing variations in speed, there are a few potential causes to consider. Here are some steps you can take to troubleshoot and fix the issue: Check the belt: The belt on the turntable may have become stretched or worn, which can cause variations in speed. Inspect the belt for any signs of damage or wear, and replace it if necessary. Check the platter: The platter may be dirty or have accumulated debris, which can cause it to spin unevenly. Remove the platter and clean it thoroughly, and make sure it is seated correctly on the spindle. Check the motor: The motor may be malfunctioning or dirty, which can cause variations in speed. Remove the motor and clean it, and check it for any signs of damage or wear. If necessary, replace the motor. Check the pitch control: The pitch control on the turntable may be dirty or malfunctioning, which can cause variations in speed. Clean the pitch control and make sure it is working correctly. Check the power supply: The power supply may be providing insufficient power to the turntable, which can cause variations in speed. Check the voltage output of the power supply, and make sure it is within the manufacturer's recommended range. If none of these steps resolves the issue, you may need to take your turntable to a professional repair technician for further diagnosis and repair.

To reset your Pioneer VSX-D711 receiver, you can follow these steps:

1. Power off the receiver.
2. Press and hold the "Advanced Surround" button on the front panel of the receiver.
3. While still holding the "Advanced Surround" button, press and hold the "Standby/On" button.
4. Continue holding both buttons for a few seconds until the display on the front panel of the receiver shows "Resetting."
5. Release both buttons.

The receiver will now be reset to its default settings. Note that this will erase any custom settings or presets that you may have programmed into the receiver. If the above steps do not work, you can also try the following:

1. Power off the receiver.
2. Press and hold the "Tuner" and "Band" buttons on the front panel of the receiver.
3. While still holding both buttons, press the "Standby/On" button.
4. Continue holding all three buttons for a few seconds until the display on the front panel of the receiver shows "Reset."
5. Release all three buttons.

Again, this will reset the receiver to its default settings and erase any custom settings or presets that you may have programmed

If your Pioneer SW-8 subwoofer is not powering on, there are a few things you can try to troubleshoot the issue:

1. Check the power cord: Make sure that the power cord is securely plugged into both the subwoofer and a working electrical outlet. If the power cord is loose, try unplugging it and plugging it back in.
2. Check the power switch: Make sure that the power switch on the back of the subwoofer is turned on.
3. Check the circuit breaker: The subwoofer may have a circuit breaker that has tripped. Check the circuit breaker on the back of the subwoofer to see if it has tripped. If it has, reset it by pushing the button back in.
4. Check the fuse: The subwoofer may have a blown fuse. Check the fuse on the back of the subwoofer to see if it has blown. If it has, replace it with a fuse of the same rating.
5. Check the auto power function: The subwoofer may have an auto power function that turns it off after a certain amount of time if there is no audio signal. Make sure that the audio source is playing and sending a signal to the subwoofer.

If none of these steps resolve the issue, there may be a problem with the amplifier or power supply in the subwoofer.

It's possible that the fuse has blown, which can happen if there is a power surge or if there is a problem with the wiring or connections. Here are some steps you can take to troubleshoot the issue:

1. Check the fuse: The first thing to check is the fuse. Make sure the receiver is unplugged from the power outlet, then locate the fuse on the back of the unit. Check to see if the fuse is blown, which can be indicated by a darkened or broken wire. If the fuse is blown, replace it with a new one of the same amperage rating.
2. Check the connections: Make sure all the connections to the receiver are secure and not loose or damaged. Check the speaker wires, power cord, and any other cables that are connected to the unit.
3. Disconnect other equipment: If you connected the Pioneer receiver to another receiver and a speaker system, try disconnecting all the equipment and connecting only the Pioneer receiver to a power outlet. If it powers on, you may need to troubleshoot the other equipment to determine if it is causing an issue.
4. Check the power outlet: Make sure the power outlet that the receiver is connected to is functioning properly. Try plugging in another device to the outlet to see if it works.

copy and paste https://www.manualslib.com/manual/1183977/Pioneer-A-307r.html#manual ..

most record players use a rubber wheel against the turntable (on the inside) to turn it.. as they get old and brittle they tend to slip a lot. a temporary fix involves cleaning the rubber piece but it really needs replacing..

It sounds like you are having an issue with your Pioneer VSA-5500 receiver not displaying or producing any sound. It's likely that the problem is related to a malfunctioning main control board or a power supply issue. Here are a few things you can try:

1. Check all the connections between the main control board, power supply, and other components to ensure that they are properly connected and not loose.
2. Check the fuse on the power supply board, make sure it's not blown, if it is, replace it with a new one.
3. Check the voltage on the power supply board, make sure the voltage is correct, if the voltage is too low or too high, the main control board may not be receiving enough power to function.
4. Check the power supply board for any signs of damage, such as burn marks or leakage, if the power supply board is damaged, it will need to be replaced.
5. Check the main control board for any signs of damage, such as burn marks or leakage, if the main control board is damaged, it will need to be replaced.
6. If none of the above steps resolve the issue, it's likely that the problem is with another component in the receiver and it will require further diagnosis by a professional technician.

It's important to note that troubleshooting and repairing electronic equipment can be dangerous, especially if you're not familiar with the device, so it's best to contact a professional technician if you're not comfortable working with it.

To factory reset your Pioneer VSX-D508 audio receiver, you will need to follow these steps: Turn off the receiver. Press and hold the "Tone" and "Speaker A" buttons on the front panel of the receiver. While holding these buttons, turn the power back on. When the display shows "Initialize," release the buttons. The receiver will now begin the factory reset process. When it is finished, the display will show "Completed." Turn the receiver off and then back on again to complete the reset. Keep in mind that this process will reset all of the settings on your receiver to their default values. You will need to reconfigure any settings that you have changed since you purchased the receiver.

There could be a few reasons why you are not getting any sound from your vintage VSX 5600 Pioneer home theater system. Here are some things you can try:

1. Check the connections: Make sure all of the cables are securely connected to the appropriate ports.
2. Check the power: Make sure the home theater system is turned on and the power cord is plugged in.
3. Check the volume: Make sure the volume on the home theater system and the volume on your TV are turned up.
4. Check the input: Make sure the home theater system is set to the correct input.
5. Check the speakers: Make sure the speakers are turned on and properly connected.

It is not recommended to attempt to reset a device with no power. If the power is off, the device will not be able to respond to any commands or perform any actions. If your Pioneer VSX-AX3 is not turning on or functioning properly, there are a few things you can try before attempting to reset it:

1. Make sure the device is properly plugged in and that the outlet is functioning properly.
2. Check the power cord for any damage, such as frayed wires or loose connections.
3. If the device is connected to a surge protector or power strip, try plugging it directly into a wall outlet.
4. Try a different power cord or outlet to eliminate the possibility of a problem with the cord or outlet.

If none of these steps help, you may need to have the device repaired or replaced.

Question edited to toss in some CAPS. Question moved from Cars and Trucks category. Service Manual links https://www.google.com/search?q=%22pioneer+rx-570%22+belt+replacement ..