20 Most Recent Black & Decker AAW100 Automatic Adjustable Wrench - Page 4 Questions & Answers

it is a type of screwdriver bit

they are typically made out of cast iron, often with little bits of concrete infused in them

The pitch of the roof is described as the vertical rise of the roof divided by the horizontal span of the roof. The pitch of the roof is known as slope, and this happens to be a tangent function. When pitches are kept below 3.5, they are considered as low pitch, and when the pitch is kept from 3.5 to 7.5, it is considered as medium pitch anything above than 7.5 is considered to be a steep pitch. Depending on your requirement and style of construction you can decide the pitch of your roof. Click on Gotcha Covered Contracting to know more about roofing.

I have a box of 5000 8mm 960/101 Vanguard Primo Staples - offer me something to cover the postage!

When you are working with brick or concrete, you should check out the Black & Decker DR670 Hammer Drill. It is specifically made to tackle this purpose.

This is just generic instructions just to give you an idea of placement and mounting. I am not sure if your vise turns or not and that would be a big factor also. It depends on where you want it, if anything is close that will interfere with the vise or whatever you have in the vise. Depends how thick the spot is where you want to mount it. If the place is not very thick, use bolt and heavy washer on top of the vise and a heavy washer, a lock washer and nut on bottom. In place of the lock washer and nut, you could use locknut. If the bench where you want to mount is too thick for bolts, use at least 2" lag bolts with heavy washers with the lag bolts as big as the vise holes will accept. You will need the vise as close to the edge without it hanging over the edge of the bench. This is so you will be able to open and close the vise without obstruction. If placement of the vise isn't a big deal, the center edge of the bench would be great although I always mount mine on one end of the bench because of better movement of the part in the vise. Goodluck.

Unfortunately you need an expensive scan tool that can read all the other individual modules of a car. The Mercedes Benz cars have many of these and without information, it is very hard to work on. It sounds like a body module is acting up.

This torque wrench requires 2 LR44 button batteries (1.5V ea). Here's an Amazon page for this type: Strip of 10 Energizer A76 LR44 1 5v Alkaline Batteries Home Depot provides the manual PDF for download on their website: https://www.homedepot.com/catalog/pdfimages/5f/5f26d0d8-9508-4807-80aa-3654f94e6609.pdf

What's your question?

If the battery has been used a lot or has not been kept charged up it likely is shot. A battery that is not used a lot should be kept charged. I keep my battery operated drill on the charger almost all the time. I have two and change them once every two weeks. Several years old and they both work good.

any wire that says batt is always live in the fuse box.

Generally the repair is more costly then just getting a new one, especially black and decker

noty a question for fixya site get the correct manufacturers site up and ask them

may get a break down from the manufacturer on line but from experience junk it and get a new one easier on the nerves and less frustration

turn the gun upside down and there is a silver slide plate left that up and there will be the location to load the brads

Have had the same problem but now it

I don't know if you have been having higher then normal humidity where you live but one thing I have done for years that is inexpensive and easy is to wipe down your tools and golf clubs when not in use then spray them with WD-40.On my tools that hang in my shop I just spray them and leave the spray on. The tools that go in my tool boxes I spray and wipe lightly then put them on paper towel liners in drawers.I have my shop in a very old building with no heat unless I'm in it and have my stove burning so my tools are subject to extreme weather conditions. I do the same thing with power tool except being careful not to get any on the motors. I spray the table,blades and fence and mitre guide on my table saw and table,supportpole,gears and spindle on drill press and leave it on. It collect a bit more dust but cleans up easy.
The main ingredient in WD-40 is fish oil so it works great at displacing water and preventing rust. Thank you.

put the knife to the wire insulation at about a 60 degree angle, and strip it like you are manually sharpening a pencil. sometimes it is easier after you heat up the insulation. or go to the store and get wire strippers for about 5$

they do make swagginhg tools that are fixed onto the yoke of a flaring kit. to hand swag, you should use the block of the flaring kit to hold your tubing. if you are swagging half inch tubing, hold the tubing up the diameter of the tube plus one eighth of an inch. tighten down the nut opposite the tube first then the closest one. this will keep the tubing from slipping.
Then hit it squarely with a hammer and it will bottom out at the flaring block. I would ease up on that last stroke to keep from cracking the tubing

Maybe it hepls you. On this website (link below) you find Fuse box layout and description for Volkswagen Transporter T5 Volkswagen Transporter T5 ESSENTIALS from September 2009 fuse box diagram...