20 Most Recent
Dewalt 18 Volt Compact Drill Kit - Page 4 Questions & Answers
I have a DEWALT DC920
try tapping on all sides of the chuck lightly with a hammer and wiggling the bit... you can also try to spray some oil into the chuck and see if that loosens the bit for you... You can also clamp the bit in a vise (or get someone with a pair of pliers) and pull, that will sometimes do the trick.
My 18 volt dewalt cordless
I would make sure that the bit is firmly installed in the chuck, you should hear clicking when the bit is tightening, this is the chuck locking itself on the but.
and when going in reverse make sure you dont have your hand or have the chuck pressed against an object.
If nether of these are the problem then there may be a problem with the chuck itself and should be replaced.
Why has my dewalt 18
It sounds like the motor is going bad. You could also try to take it apart and clean and relubricate the gears and shafts whith grease.
How do I change the drill bit?
you would hold chuck in a firm grasp as your hand around a pipe and hold tight,run drill in reverse and that should loosen the chuck and the bit. If its to tight for your hand get a pair of channel locks and hold chuck.
I have a new DeWalt
Try wrapping a cloth around the chuck while unscrewing it by hand. This may give just enough grip to undo it.
How do i remove the
There are to parts to the chuck. You hold the ring at the edge of the chuck from turning, and then you turn the part after that, ccw to release.
Can't remove bits
I had this problem on my De Walt DW912- I simply couldnt turn the keyless chuck to remove the screwdriver bit and there was no obvious reason why.
I placed the unit on a solid surface so that the chuck/ drill bit was pointing vertical. I then used a mallet and a metal chisel to gently tap each of the 3 chuck jaws back into the chuck body. It worked!
Turned out that there was the absolute tiny amout of corrosion between the jaws, and the chuck and my tapping had just broken the siezure. I now remember that it started to rain slightly last time I used it.
Some spray release agent or perhaps WD40 would probably have done the same job but I wouldnt have believed so little corrosion could have done this so didnt realise this was the problem.
The drill works but you can hold the chuck while
could be a couple problems, is the switch selector fully engaged in hi/low and is the clutch seting set for the proper torque.If both OK then I would have to think that you need a new clutch assembly
Remove dewalt chuck that is stuck
down inside the chuck head itself is a allen head screw,, it has reverse threads on it. if you have already removed this screw and the chuck is still stuck then you will need to use a small gear/pulley puller to get it to release.
(( note: if you do not have access to a puller -- stop by you local Dewalt repair shop and I am sure that they will pull the chuck off with their puller at no charge to you )).
c...
Using a garden auger with the torque set to the
Yes, luckily Dewalt is taking care of you. You might want to look into a 1/2' drive electric model (sorry with a cord) Alot depends on how hard the ground is but in the long run the big electric will handle about anything you throw at it. Check Sears or Home Depot both good sources for good tools
Can't get the chuck off my DCD950
if trying to remove the keyless chuck/open chuck and down inside is a hex screw useing a hex wrench place long end in screw and give the wrench a sharp rap with a hammer to break loose/....(not sure if dewalt has left or right hand threads)and i have had to rap a drill with a rag and place in vice to help hold it.......hope it helps
The 14 Position adjustable torque control How to
The torque settings on a drill will stop the drill from driving the screw ( or what ever you are tightening ) when it reaches a specific "tightness" . For example; the setting "1" will only tighten a screw a very little bit, while " 14 " will tightten the heck out of it.
Note: once the screw has reached it's specific torque ( or tightness ) the drill motor will continue to turn but it will disengage the driver, making a kind of grinding sound,it's perfectly normal so don't be alarmed.
Not finding what you are looking for?