GE Security DVMRe-16CT-600 16-CHANNEL Color Triplex Multiplexer-Recorder with 600-GB Hard Drive, Ethernet - Answered Questions & Fixed issues

If memory serves me correct, most of the GE/Truvision etc. DVRs have to be sent back in for the password to be defaulted. I may be incorrect on this, will double check.

Hi I do NOT think that this adapter will/would work, you see even though one may think it should, this unit actually requires a native drive, not an adapter, you need to remove the adapter and use a drive that direct connects then it will work. It is really that simple.
Usually one Formats, on a PC via a USB dongle etc, and gets the HDD all ready to install, then, one plugs it into the interface and power, and then the unit should "See" the new HDD and perform it's "Housekeeping duties" on it, and make it available for use. Alternatively, one can simply hook it up, direct, and then the device should again "See" it, and the device will/should then Format it itself, and make it ready to use, the reason we may do in on a PC, is sometimes this is where there may be problems, formatting etc, that will not happen if done on a PC first. If done on a PC, ensure you format the correct format, usually FAT32, but not always.
There are a few tutorials online, perhaps it may pay to have a look for one, and follow it to the letter, to get the best result.

3123
3477
6321
1111

I would switch monitors and see if the problem still exists. Sounds like the monitor not the Dvmre.

pressing the corresponding number button will bring that camera up full screen. the buttons surrounding the A - B output source button will change the way your cameras are multiplexed on your monitor. you can also change which picture displays in each box including multiples of 1 camera by pressing the enter button on lower right and using the jog wheels to move (inside wheel controls up and down- outside wheel does left and right) the highlighted number where you want to put the cameras image. press the associated camera number you want there and it appears. press enter to lock the screen.

From the user manual page 71:
5.2 Quick Archive to CD
Archive to CD on the Disk Analysis Screen by selecting the time and date and pressing the record
button. The QuickWave Setup must be set to ON from the Archive Setup → Quick Wave Setup menu
(see section 3.15). The Archive Incident menu should appear.
1. Use the Jog to modify the time parameters and use the
Shuttle to move between the Start and Stop fields.
2. Press the Record button on the front panel when satisfied.
3. The CD Writer will open the CD tray when completed.
The video may now be viewed on any PC equipped with a CD-ROM.

You can download the complete user manual here:
http://www.gesecurity.com/portal/site/GESecurity/menuitem.f76d98ccce4cabed5efa421766030730?selectedID=1965&seriesyn=true

The factory default code to reset the system is 8111, however this will reset all program functions back to the factory settings, with the exception of the time and date. The default Operator code to use the system is enter, enter, enter, enter. This should allow you to operate the system.

Hit menu button, top right of jog, installer code is 3477, then use jog and dial to change settings. These must be done locally!

Check in the settings and make sure it is selected to be on.

Go to this site and download WaveReader software.
http://www.gesecurity.com/portal/site/GESecurity/menuitem.11620ebca5cc0a06574efe10140041ca/?vgnextoid=4f9fe4997e789110VgnVCM100000592d7003RCRD

Please find the following passwords.

Ten and Sixteen-Channel Units
Password Type Access Level Function Changeable by user?
Default Password Operator Operator Provides access to the Operator and SystemView menus. Press ‘ENTER’
4 Times

Installer Installer Provides access to all on-screen menus. Password 3 4 7 7

Factory Defaults Installer Resets the multiplexer to the factory defaults (except the time, date, email addresses, and email
IP address). Password 8 1 1 1

Language Installer Provides access to the On-screen
Language menu. Password 5 4 1 5

Ethernet Access Reset Installer Deactivates the ethernet
password, so that the unit may be accessed by any PC equipped with WaveReader. Password 1 1 1 1

I have strongly recommended that change your power supply with the same specification voltage and amp. I have installed so many GE DVR's most of DVR's restart when the power supply is not working properly or HDD have bad sectors. I also recommend use the scan disk on you HDD for proper checking of your HDD.

FROM
AI

check out the manuals for customisation http://us-alarm.com/files/NX1448E(English%20Fix).pdf https://www.google.com/search?q=GE+NX-1448E+manual ..

All wireless security motions have a 3 min delay built into them. This means that whether the alarm is set or not when the motion detector picks up motion it shuts down for 3 min and will not pick up motion. This is done to conserve battery power. So I always advise customers to arm the system and stay away from the motion for 3 min total. example: 60 sec to arm system + 2min wait time. then try to trigger motion. If this does not help and assuming batteries are good, you'll need to replace motion. Good luck. This may help https://al.ly/vR54zP

I would start by power cycling your system. Remove the battery & power. After waiting 10 minutes or so reconnect the battery and then power. Other than that you need to be a bit more specific with your issues.

I usually find remotes on Ebay for anything cheap.

Try disarming system twice to get the fire zone to reset. If that doesn't work, try to downpower the entire system, including back up battery then re-power the system with the back up battery first.

https://manuals.solidsignal.com/19297.pdf

you need to get the installer code, then enter programming mode to delete the sensor.