D-Link RangeBooster G WBR-2310 Wireless Router (WBR2310) - Page 8 - Answered Questions & Fixed issues

connect your computer to the router by an ethernet cable. Open Internet explorer or FIREFOX. Type the roiuter's default IP-address (if not known: its either 192.168.0.1 or 192.168.1.1 or 192.168.0.0 or 192.168.1.0... keep trying until you're answered and asked for the password to enter the router (either attached on the router, in the manual or try: user: admin password: admin or password: password. Whgen you're in you'll find many checkboxes you could fill oput or notr; Easyway: give your net a name (SSID), then choose the network access security (set it to wpa-psk), choose a password and enable DHCP (then the router does the rest). Disconnect, look if the computer sjhows reception of your netwoirk by displaying its name. then connect. You will be asked for the password you chose. Done.

the password was wrong just reset the modem and reconfigure once again other wise in the address bar type the default gateway its ask for user name and password just enter the user name and password you can find the user name and password at the manual of your router it will login to your modem page in that you can find the option called security in that security you can find your old password

Thank you

This service rests with your service provider.
So, you need to contact your service provider to reset your credentials.

look on the back of the router, there is a hole, its the reset button, use a paperclip or something to push in there for 30 seconds or so
Your router is reset

first connect your computer to one of the LAN ports of the router...
Then check your ip address for LAN under network connections...

If you get any 169.254.X.X ip address then you need to reset the router...

if you get some other ip address then note down the default gateway and try with that...

try this...

goto run > type "cmd" and hit enter >> command prompt will open...

in command prompt type this

start iexplore 192.168.0.1

and hit enter

You will need to check the wireless settings of the router
is there any computer connected to the router ?
If yes then you can open the router set up page on that computer.
Router set up page is the page where you can check all the wireless settings of the router.

Click here for step by step instructions

remove the cat5 cable end that goes from your internet connected computer to your router; remove the end of this cable from your router ; remove your modem to router cable end from your modem put the internet computer cable into where the router cable was in the modem; unplug then: plug in your modem; wait for the modem to reboot; verify that the internet computer is online then swap the cables back where they were
you should now be able to connect your laptop wirelessly to the internet.

Maybe the router is already defective. I guess you should replace it with a new one. Because you cannot also repair that due to its already component level type of repair.

Hi mech_warrior,

Press the reset button of the d-link router for 30 seconds, unplug and plug the power cord.

MAC cloning is used for Cable ISP configuration but that should not affect the router's functionality (odd router behavior) ;-)

That should do it!

Angel

Get the drivers from www.dlink.com/support

>If you're trying to put password for the Router, then type "http://192.168.0.1" into the address bar, then hit "Enter."
>Use "Admin" as the username and leave the password blank when the login screen appears.
>Please click on Administrator settings and change the User Name and Password.

If you're trying to put a password/secure the Wireless network, then follow the steps:

>In the Router setup page, click on Wireless Settings.
>Under Wireless Security Mode, select Security Mode: WEP/WPA/WPA2.
>Enter the Security Key manually or enter the Phrase to generate the Security key automatically (only in WPA/WPA2) and save the settings.
>Please note the Security Key to connect to the Wireless Networ.
>The Wireless is secured now.


Good Luck!!!!

there is posibly a sync problem try using two dlink routers .

please observe signal strength as when you are connected to network and till you drop off, there may be distraction in signal strength while you are connected and when you check it again, it comes to good again.

Normally, you can just plug it in and go. Most routers will allow connections with basic settings. IF you must have the easy-start disc, you can also get the program either online via download by searching on the manufacturer's website, or you can order the disc from the manufacturer.

You could also buy a new one, use the disc, then take it back to the store and say it's not "right for you". They'll return it and give you your money back.

mcdevito75 here Try to remove the plug for your wireless from the back of your computer for 1 minute then reconnect to your computer and start again.

How to secure the wireless network

You want to secure the wireless network.
Is there any computer connected to the router with the Ethernet cable?
If not then you will need to connect the computer to the router with the cable.
Check the IP address on the computer. Open the router set up page.
Once you open the set up page, you will find the option to make it secured

Click Here for step by step instructions

check your configuration on your PC, see if it is pointing on a DNS that was previously identified. Make sure it is in automatic. also check your router as well as the signal strength. I suggest don't use the router and directly connect your computer to the internet connection just to check the speed and compare. if it is ok then your router is your problem. check its configuration and set it properly.

Are you trying to set up router ?
You can set up your router manually, without the CD.
Make sure that your computer is able to go online directly through the modem.
If your computer is able to go online through the modem, that means the modem is working fine.
You will need to connect the computer to the router and the modem to the router.
open the set up page of the router and change the settings of the router according to the ISP.

Click Here for more information about the routers and network

Just reset your router and use (admin) for user name and password. To reset your router you can see a small hole in your router which is labeled reset. Use a pin and insert it to the hole and push.

it depends on the router you use go to start all programs under accessories look for Run, cick run then in the run window typ CMD then press enter, then in the Dos prompt type IPconfig then press enter it will show the ipaddress and default gateway ofr your router copy the default gateway type it in Interent explorer tha should open a page where your router settings are it will ask for apassword and user name which you must know to access the router settings and be able to get the network key from the router to be able to input in your computers wireless settings to gain acces to the router and wireless internet, Call your internet service provider if you can remeber having a user name and password,

for Edimax routers user name is admin password should be 1234, linksys user name admin password eitheradmin as well or leav it blank, and yeah for further info under the router there should be a sticker with the router default user name and password on it if not on the sticker call your ISP or whoever provided the router to you for the router user name and password ^_^ hope this info will be helpfull to you ^_^