D-Link RangeBooster G WBR-2310 Wireless Router (WBR2310) - Page 5 - Answered Questions & Fixed issues

Go to run command, type "cmd" and hit enter, this will give you a black command prompt box. In there type "ipconfig" and hit enter, look for the line saying "default gateway" - make sure thats the ip address you are trying to go to as that is the address for your router.

This type of problem can be related to a firmware issue on the router and what you can do here to try in correcting the problem is to do first some changes on the wireless settings of the router like the channel and play around with it and look for a stable channel but if still the same problem do a firmware upgrade on it.

Ads by Google Dell Networking Solutions -

www.Dell.com/NetworkSolutions
Managed & Unmanaged Network Connectivity For Small Businesses.
High-End Mikrotik Router -

www.MikrotikRouter

On the iPod touch, select "Settings"
On the second line, you should see "Wi-Fi", touch on the right side of this bar, this will bring you to the menu to choose a network. From there, choose the network you want, and type in the security code if need be.
.
As a note, if you go back to settings, the 1st line is "Airplane Mode", make sure this option is "OFF".

Try changing channels, it could be RF noise from some near by device, you could also try updating the firmware to the latest version, some times moving the router in a different location could help.

Good luck!

You'll need to reset your router to its factory default condition, then re-enter your configuration information (ie, set a new wireless password, etc.).

Use a paperclip or similar item to (while the router is on) depress the "Reset" switch on the back of the router, hold it for 10 seconds, then release. This will reset it so you can reconfigure it as if it was new using the web interface.

Hope that's helpful.

If your trying to log into your router, try using 192.168.0.254 but do it on cable until you have the router configured for wireless. Normally, unless it was changed by your service provider, the router home address is 192.168.0.254.

NAT STRICT

Step 1 : Connect Router - Computer ( Wired )

Step 2 : Open Router setup by typing http://192.168.0.1 on the address bar of the internet explorer

Step 3 : The Default Password is admin

Step 4 : At the top Click Advanced

Step 5 : On the left Click Firewall Settings

Step 6 : Enable DMZ

Step 7 : give the IP Address of the Xbox/PS3/Wii in it

Step 8 : Uncheck the option Enable SPI

Step 9 : Click Save Settings

Step 10 : Test the connection

let me know if this works

Regards
TOM

There are multiple versions of both of your routers, you can click on your version and try there tech info from there. If you have no luck, just post the right versions here and I'll see what I can do for you.

.............................................................................................................

There are multiple revisions of the WBR-1310, each with revision specific drivers, firmware, installation guides, and other resources.

• WBR-1310
• WBR-1310_REVB
• WBR-1310_REVD

There are multiple revisions of the WBR-2310, each with revision specific drivers, firmware, installation guides, and other resources.

Go to there support page and click on your model.

• WBR-2310
• WBR-2310_REVB

http://www.dlink.com/products/default.aspx?pid=WBR-2310&tab=3

Try
username =admin
password =password or admin

If you only have a modem, you need to get a router.
If you have a router:
You do not need a cd to install on your desktop. I assume that you have a wireless adapter in your desktop, right?
all you have to do is click on the wireless icon in the tray, select "view available networks" then select your network and type in your security key if you have one setup. I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Below is a link to dlink that gives you 2 options for configurating your router.

http://support.dlink.com/emulators/wbr2310/index.htm

I hope this helps

Go to D-Link - TechSupport FAQ.

If you need more help come back.Post / thumbs / testimonial are welcome!

One cable goes from the router to the modem and then the power cord. thats it.

if you forget your given password then only it will prompt to tell you that you are not admin. I am sure u have forgotten your password.

1.Powercycle equipment (Unplug and plug back in)Wait 15 seconds then plug back in.
2.Check connections the Ethernet cord from modem should be plugged into back of router into internet port.
3.If modem runs off signal from a local tower and there is not sufficient signal on the modem you will need to contact your ISP ( Internet Service Provider) to check for outages if not skip to step 4.
4.Open your network connections window.
A.Windows XP:Start/Run/Type ncpa.cpl this will bring you to network connections.
B.Windows vista/7 Start/Search bar Type ncpa.cpl
5.Windows XP:Right click on Local Area Connection and click properties,
A.Click Internet Protocol and hit properties ensure Obtain ipaddress automatically and Obtain DNS service automatically is checked if not check both and close window.
B.Windows Vista/7 Right click Local Area Connection and click Properties, Uncheck Internet Protocol Version 6 and click on Internet Protocol Version 4 and hit Properties Ensure Obtain ipaddress automatically is checked as well as DNS server.
6.You will need to manually renew ipaddress if this does not work
A. Windows XP:Start/Run/Type CMD and hit enter,
B.Type ipconfig /release
Then type ipconfig /renew then restart computer
A.Windows Vista/7 Start/All Programs/Accessories/Right click Command Prompt and hit run as administrator.
B.Type ipconfig /release
Then type ipconfig /renew restart your computer
7. If this does not help run an Antivirus. Hope this helps Happy Thanksgiving

Connect a LAN cable from the computer's LAN port to the D-Link.
Open a browser and type in the D-Link's configuration URL
http://192.168.0.1
the default login = admin
The default PW = blank (just press enter)
You can now go to Change password.
To secure your wireless network from unauthorized access, please click on this link and follow my instructions :-
http://www.fixya.com/support/r3559128-wireless_router_security

D-Link - TechSupport FAQ..

If you need more help come back.Post / thumbs / testimonial are welcome!

The closer the router to devices the better.if signal is the issue get a router repeater.

If you need more help come back.Post / thumbs / testimonial are welcome!

D-Link - TechSupport FAQ.

If you need more help come back.Post / thumbs / testimonial are welcome!