D-Link RangeBooster G WBR-2310 Wireless Router (WBR2310) - Answered Questions & Fixed issues

Please reset the router and also remove the network from the devices and reconnect with the password. for more visit www.leadingpcfix.com

restarting constantly indicates a loss of connection with the server talk with your service provider to check the connection for continuity

If all lights are lit regardless of anything connected then you may have a hardware failure. Try a hard reset by putting a tip of a paperclip into the small reset hole while powered on for 10 seconds. See if that resets you router - if not then it is dead.

The final solution is a factory reset of your router. You can do a factory reset by logging into the router using you browser. Go to the settings and perform a factory reset If you forgot the router password, you ill have to do a factory reset by locating a small hold on the back of the router and insert the tip of of paper clip for about 10 seconds while the power is on. The router will be reset to out of box status and then you can set-up form scratch.

Login in using your browser and go to the wireless settings and set-up a wireless password/key. Remember the key because each device will now need it to connect. You can also turn OFF Broadcast SSID and your network name will not be shown on anyone's device. You must remember the network name when using this method.

You can download a manual or quick set-up guide from the D-Link web site support section. You can connect to the router using a LAN cable or to wireless dlink and use the IP address of 192.168.0.1 should allow you into the set-up menu. The default router login is ADMIN and password is blank. You should be able to set-up the router without a CD.

Login in using your browser and go to the wireless settings and set-up a wireless password/key. Remember the key because each device will now need it to connect. You can also turn OFF Broadcast SSID and your network name will not be shown on anyone's device. You must remember the network name when using this method

Try rebooting the router. Login into the router to see if the wireless is turned ON and set to FULL power. If this does not work, The final solution is a factory reset of your router. You can do a factory reset by logging into the router using you browser. Go to the settings and perform a factory reset If you forgot the router password, you ill have to do a factory reset by locating a small hold on the back of the router and insert the tip of of paper clip for about 10 seconds while the power is on. The router will be reset to out of box status and then you can ssets-up form scratch.

Login into your router and in the wireless section you can enable guest access. On some models you can have the guest mode access only the internet, and you can select whether you want to have a password for the guest mode or not.

One easy trick is to change the default IP 192.168.0.1 to something else in addition to password protecting the login to the modem. Make sure you save the new IP address.

If you dont know your wpa network key try to reconfigure your wireless network again.

Access the configuration page of your router.
>Type on the address bar 192.168.0.1
>On login type Admin leave password blank. if you set up a password or the login page use that one.
>Once inside the Dlink Page
>Clik Setup and on the left side click wireless setting.
>If given the option to click on manaul wireless connection setup click on it.
>Once you have the wireles window
>try to change the network name to a new one and scroll down
>Under security choose WPA security (enhanced)
>Scroll down and under the Passphrase type in your new network password or security key and confirm it.
>Click on Save Settings
>If it asks you to reboot then reboot it, if not, its ok.

This model does not have a WPS button, so you will have to configure it manually.

Talk to your shipper and place a track on it

Call your ISP and ask to cahnge it.

Can i have more info.Channel is related to the router itself not the printer.The channel is acquire by the router automatically.In order to cahnge it you need to access the router configuration.

You will have to set-up using your router. Please use the following source: http://www.wikihow.com/Setup-D-Link-WBR-2310-Wireless-Router hope this helps and please don't forget to rate.

See section 3 page 15 of the user manual.

Available here:

http://www.netwood.net/support/manuals/D-Link_WBR2310_manual_10.pdf

http://www.netwood.net/support/manuals/D-Link_WBR2310_manual_10.pdf

Use the On-Line setup. User setup manual: http://www.netwood.net/support/manuals/D-Link_WBR2310_manual_10.pdf

This may help: http://www.dlink.com/us/en/support/product/wbr-2310-rangebooster-g-router