20 Most Recent D-Link RangeBooster G WBR-2310 Wireless Router (WBR2310) - Page 5 Questions & Answers


yes if u have the ssid disabled it wont detect it u have to log into ur router and set it to broadcast the ssid

log into the router and click on advanced wireless settings and clear the check mark where it says disable ssid and save settings

also is ur wireless card enabled on ur computer

D-Link... | Answered on Feb 05, 2011


ok you need to open your internet browser and in the address bar enter 192.168.0.1 then a login prompt will come up enter admin for the user name and leave the password blank. then when you get to the router configuration page select the setup wizard and follow it to the end and that should be it, if you still have problems uninstall the setup that you did from disk they may confict. ok hope that helps and just in case you dont have the manual here is the link to the support page for your router http://www.dlink.com/products/?tab=3&pid=WBR-2310&rev=WBR-2310 please let me know if i can assist you any further and how you go.

D-Link... | Answered on Feb 04, 2011


You need to delete the original wireless setting from the printer and establish a new one with the correct credentials to match your new security.
I hope you find my reply helpful.

D-Link... | Answered on Feb 04, 2011


How to install Verizon 7500 DSL Router !

Plug the Ethernet cable into the Ethernet jack of the computer. Connect it to one of the LAN ports on the back of the router.

Connect the telephone cord to the telephone jack on the back of the router. Connect the other end to a working telephone jack.

Power on the computer and the router.

Insert the installation CD into the computer's CD drive. Double-click on the installation icon that should appear on the screen.

Select the SSID for the router when prompted. It should be printed on the back of the router.

Enter the security password when prompted; it also is printed on the back of the router. Open a web browser to connect to the Internet.

Connect DLink WBR 2310 Router to another router(Verizon 7500 DSL), please follow the steps below:

1. Plug the power into the router. Connect one of your computers to the router (LAN port) using an Ethernet cable. Make sure your IP address on the computer is 192.168.0.xxx (where xxx is between 2 and 254). Please see the Networking Basics section for more information. If you need to change the settings, write down your existing settings before making any changes. In most cases, your computer should be set to receive an IP address automatically in which case you will not have to do anything to your computer.

2. Open a web browser and enter http://192.168.0.1 and press Enter. When the login window appears, set the user name to admin and leave the password box empty. Click OK to continue.

3. Click on Advanced and then click Advanced Network. Uncheck the Enable UPnP checkbox. Click Save Settings to continue.

4. Click Setup and then click Network Settings. Uncheck the Enable DHCP Server server checkbox. Click Save Settings to continue.

5. Under Router Settings, enter an available IP address and the subnet mask of your network. Click Save Settings to save your settings. Use this new IP address to access the configuration utility of the router in the future. Close the browser and change your computer's IP settings back to the original values as in Step 1.

6. Disconnect the Ethernet cable from the router and reconnect your computer to your network.

7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug anything into the WAN port of the D-Link router.

8. You may now use the other 3 LAN ports to connect other Ethernet devices and computers. To configure your wireless network, open a web browser and enter the IP address you assigned to the router. Refer to the Configuration and Wireless Security sections for more information on setting up your wireless network.









D-Link... | Answered on Feb 01, 2011


In order to get your router back to the original settings, you must push in the reset button (usually on the back of the router) for somewhere between 10 and 30 seconds depending on the router. You may need a pin or something small to push in the button, because it can be recessed. Once you have reset the router, the username and password will be changed to the defaults, admin and password, respectively. One thing you must remember is that resetting the router will change all of the router settings back to the factory settings. This means you will lose all of the changes you made since you got the router. Make sure to write down any things you've changed, so you can change them back after the reset. Also, I recommend updating to the latest firmware after the reset.
If you need more help post back! Thumbs and testimonial are welcome!


There a great article at General Router Setup.
If you need more help post back!
Thumbs and testimonial are welcome!

D-Link... | Answered on Feb 01, 2011


There is a great article at Working with Windows Wireless Networks
If you need more help post back! Thumbs and testimonial are welcome!

D-Link... | Answered on Jan 31, 2011


Perform a D-Link Router reset

Step 1 Locate the reset pinhole on the back of the unit.

Step 2 With the unit powered on, press and hold the Reset button.

Step 3 Hold the Reset button for about 10 seconds.

Step 4 Release the Reset button.

Step 5 The unit will reboot. Allow 20-30 seconds before reconnecting.

Step 6 The device is now at factory defaults.

Note: Do not recycle power during the reset procedure. The default user name for most D-Link devices is admin and the password is left blank.
When it says hold for about 10 seconds, don't hold for more than ten seconds or the procedure will likely fail, if ten seconds doesn't work try 5 seconds.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe




I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

D-Link... | Answered on Jan 29, 2011


Base from the description of your problem this is a clear sign of a problem with the router,what you can do here is to upgrade or reflash the firmware of the router, you can get the firmware from Blink website and if still the same after doing that the router is already having a hardware problem and better have it replace.

D-Link... | Answered on Jan 26, 2011


There a great article at General Router Setup.
If you need more help post back!
Thumbs and testimonial are welcome!

D-Link... | Answered on Jan 21, 2011


You need to configure your router with below method. Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. Then set WAN settings as internet service provider settings enable DHCP. . Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.

D-Link... | Answered on Jan 20, 2011


If your OS is Windows there is a good tutorial at -> Working with Widows Wireless Networks

That can help you out to configure your wireless networks.

If you need more help post back!
Thumbs and testimonial are welcome!

D-Link... | Answered on Jan 17, 2011


To secure your wireless network from unauthorized access,please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

D-Link... | Answered on Jan 16, 2011


Here is a direct link to show you how to setup your router simply click product manual and it will auto download it for you thank you have a good day.
http://www.dlink.com/products/?tab=3&pid=WBR-2310&rev=WBR-2310

D-Link... | Answered on Jan 14, 2011


Hi,

In order to find the wireless security password of your Dlink wireless router G WBR-2310 , please follow these setps

1. Open up the internet explorer in the computer in which you are online and clear the address bar and type in the number 192.168.0.1 and hit enter.

2. You will be logged into the D-Link router setup page .

3. Under the SETUP tab, in the left hand side, click on WIRELESS SETTINGS? you will find Wireless security Mode under which you can find the password for the wireless settings.

Good Luck!

Thanks in Advance!

With Regards,

Prema.

D-Link... | Answered on Jan 11, 2011


Go to run command, type "cmd" and hit enter, this will give you a black command prompt box. In there type "ipconfig" and hit enter, look for the line saying "default gateway" - make sure thats the ip address you are trying to go to as that is the address for your router.

D-Link... | Answered on Jan 07, 2011


This type of problem can be related to a firmware issue on the router and what you can do here to try in correcting the problem is to do first some changes on the wireless settings of the router like the channel and play around with it and look for a stable channel but if still the same problem do a firmware upgrade on it.

D-Link... | Answered on Jan 05, 2011


On the iPod touch, select "Settings"
On the second line, you should see "Wi-Fi", touch on the right side of this bar, this will bring you to the menu to choose a network. From there, choose the network you want, and type in the security code if need be.
.
As a note, if you go back to settings, the 1st line is "Airplane Mode", make sure this option is "OFF".

D-Link... | Answered on Jan 05, 2011


Try changing channels, it could be RF noise from some near by device, you could also try updating the firmware to the latest version, some times moving the router in a different location could help.

Good luck!

D-Link... | Answered on Jan 04, 2011


You'll need to reset your router to its factory default condition, then re-enter your configuration information (ie, set a new wireless password, etc.).

Use a paperclip or similar item to (while the router is on) depress the "Reset" switch on the back of the router, hold it for 10 seconds, then release. This will reset it so you can reconfigure it as if it was new using the web interface.

Hope that's helpful.

D-Link... | Answered on Dec 31, 2010

Not finding what you are looking for?
D-Link RangeBooster G  WBR-2310 Wireless Router (WBR2310) Logo

589 questions posted

Ask a Question

Usually answered in minutes!

Top D-Link Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Mike

Level 3 Expert

4363 Answers

Are you a D-Link Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

D-Link Computers & Internet

  • D-Link Computers & Internet

Most Popular Question

password protect admin 192 168 0 1

  • Computers & Internet
Loading...