20 Most Recent D-Link RangeBooster G WBR-2310 Wireless Router (WBR2310) - Page 3 Questions & Answers


In Internet Explorer, type "192.168.0.1" into the address bar. The Username will be "admin" and the password should be left blank. Click on the "Setup" tab on top and "Wireless Settings" on the left. This is where you can find/change your wifi network info. Don't forget to SAVE your changes.
Let me know if this helps you!

D-Link... | Answered on Oct 04, 2011


Streaming video , stopping and buffering is due to slow connection speed. HD movies involve loading a lot of data and hence take a lot of time to buffer. Switch to non-HD video mode and see if it streams without pauses. If that does not fully resolve the problem , you will need to go for a faster internet connection.

D-Link... | Answered on Sep 16, 2011


you need to enable the wireless option in ur wireless router

D-Link... | Answered on Aug 28, 2011


There are Old computers cant conect to the higher frequencies of the new routers so if you have tested the router on a newer computer and its working i suggest you either:

1. connect by cable.
2. buy a new network card.
3. buy a new computer.

(Also the antenna can be lose or be broken just screw it lose and check.)

D-Link... | Answered on Aug 23, 2011


Assuming you have access to the router, the router has a reset button on the back, which must be pressed for about 30 secs to 1 minute, until the router lights flash off and back on. This will result in a total wipe of all settings and restore it back to factory. This will result in the loss of all previous settings and may cause your internet access to stop working until any custom settings (if used) are re-entered.

Once the factory reset is complete, you can access most D-link routers by surfing (with web browser) http://192.168.0.1. when prompted, you will need to enter the default username and password which is admin / admin or admin / leave blank.

Once you are logged in you can then access your router to restore the desired settings.

D-Link... | Answered on Aug 11, 2011


With the router on, hold down the "reset" button on the back for 10 seconds. This will reset your password and restore factory default settings.

D-Link... | Answered on Jul 28, 2011


First power off the D-Link for 15 secs, reconnect the power and then reboot your computer. If your computer cannot connect to the D-Link and the Internet then -
I suggest you reset the D-Link back to the defaults and configure it again.

Press and hold the RESET button at the back of the routerwith the power ON until the LEDs flash at the time the release the RESETbutton.
Connect a LAN cable from the D-Link to your laptop/computer's LAN port, openthe browser on your laptop/computer and enter the D-Link's configuration URL..
http://192.168.0.1
The default login = admin
The default PW = blank (just press Enter) You can now change the default password.
You can now configure the wireless settings. Now configure the wireless card in your computer/laptop withthe router's wireless settings.
To secure your wireless network from unauthorized access,please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

D-Link... | Answered on Jul 21, 2011


Welcome to FixYa
Dear user
You have to Reset your Modem by pressing RESET button with a paper clip for 30 seconds[Router must be ON when doing this Process].After that your Password will be removed. Now you can use it. You can further go to router page only if need any modification.
Hope this helps..THanks for COnnecting FixYa...

D-Link... | Answered on Jul 15, 2011


The Real Problem with this router is the Atheros chip inside overheating. The remedy is to install a heat-sink on the chip. Also, these routers have a history of the ethernet pins crossing and jumping into the wrong slots, examine the ethernet pins very carefully and attempt to straiten them.
To test my theory, Get a beer cap and take the plastic seal out of it so that it is bare aluminium on the inside of the cap, next put a drop of heat sink grease on the outside of the cap, (if you are too cheap to get some or are in a hurry, use a drop of toothpaste) then stick it on the atheros chip inside and fill the beer cap with vegetable oil, (Use vegetable oil instead of water because if you spill it on the main board, it will not cause damage.. IF YOU MUST USE WATER, be sure to NOT SPILL it on the board.)
After you have tested it and it works, Consider getting a small cpu heatsink, Should work fine without a fan.
Thanks
Vince

D-Link... | Answered on Jul 09, 2011


It appears you are not using the wireless connections on both the routers and the reason for using Router B was that there were insufficient LAN ports on Router A to connect to the two workstations that are connected to Router B.
To simplify your network, I suggest you replace Router B with a network hub or ethernet switch and connect the two workstations to this network hub/switch, then configure these two workstation to Obtain an IP address automatically. Router A will then issue IP address to these workstations via the network hub/switch.

D-Link... | Answered on Jul 09, 2011


You can also configure it with below method.
Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. Then click on WAN settings set it as your internet service provider settings enable DHCP Then click on wireless and enable it. . Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.

D-Link... | Answered on Jun 27, 2011


Use an Ethernet cable to connect your computer to one of the LAN ports.
Click Start
Click Run
Type CMD
Press Enter
Type IPCONFIG
Press Enter
Look for a line of output like:

Default Gateway . . . . . . . . . : 123.468.32.1

Start Internet Explorer
Type http://123.468.32.1
Press Enter
Login to your router
Click to run the "Wireless Networking Setup Wizard", to:
1. set an SSID
2. set an encryption-level, e.g., 'WPA' or 'WPA2'
3. set a password for your network
Click OK to restart your computer

Use your wireless device to connect to that SSID, using that password that you set.]

D-Link... | Answered on Jun 06, 2011


If you have not changed the default login to the router then the login is admin and the password field is blank.

However, if you have changed the default login and do not remember it you will need to press the reset button on the back to restore the router to it's factory default settings then you can use the login above.

Hope this helps!

D-Link... | Answered on May 03, 2011


go to this website
http://www.dlink.com/products/?pid=WBR-2310
pick either wbr or wbr rev that you own.
then go to support resources and click on additional downloads.
you will see a link to the setup file for your specific router model

D-Link... | Answered on May 01, 2011


Try resetting the D-Link back to the default setting and configure it again.
To reset the D-Link back to the default settings -
Press and hold the RESET button at the back of the router with the power ONuntil the LEDs flash at the time the release the RESET button.
Connect a LAN cable from the D-Link to your laptop/computer's LAN port, openthe browser on your laptop/computer and enter the D-Link's configuration URL..
http://192.168.0.1
The default login = admin
The default PW = blank (just press Enter) You can now change the default password.
You can now configure the wireless settings. To secure your wireless network from unauthorized access,please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

D-Link... | Answered on Apr 14, 2011


When I write my name and password it dosent continue

D-Link... | Answered on Mar 29, 2011


There is no WPS button on the WBR2310 router. Simply connect to it like you would any other device, such as a computer.

D-Link... | Answered on Mar 26, 2011


In order to get your router back to the original settings, you must push in the reset button (usually on the back of the router) for somewhere between 10 and 30 seconds depending on the router. You may need a pin or something small to push in the button, because it can be recessed. Once you have reset the router, the username and password will be changed to the defaults, admin and password, respectively. One thing you must remember is that resetting the router will change all of the router settings back to the factory settings. This means you will lose all of the changes you made since you got the router. Make sure to write down any things you've changed, so you can change them back after the reset. Also, I recommend updating to the latest firmware after the reset.
If you need more help post back! Thumbs and testimonial are welcome!

D-Link... | Answered on Mar 08, 2011


try using a paperclip and resetting the router on the back or bottom somewhere just push the little rest button in and hold it there for 30+ seconds

D-Link... | Answered on Mar 06, 2011


hey,

Login to the routers home page (details under neath or behind the router). Once you login, go to wireless--> settings or wireless security page and then choose WPA2 or WPA PSK and enter the password and save the changes. After save, you will need to re-establish the connection to your laptop and you will be prompted for a password on the computer.

Cheers!!!

D-Link... | Answered on Mar 04, 2011

Not finding what you are looking for?
D-Link RangeBooster G  WBR-2310 Wireless Router (WBR2310) Logo

589 questions posted

Ask a Question

Usually answered in minutes!

Top D-Link Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Mike

Level 3 Expert

4363 Answers

Are you a D-Link Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

D-Link Computers & Internet

  • D-Link Computers & Internet

Most Popular Question

password protect admin 192 168 0 1

  • Computers & Internet
Loading...