20 Most Recent Amana AER5515QA Electric Kitchen Range - Page 2 Questions & Answers

Thanks for your question!

I'm sorry that you haven't received an answer yet.

The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:
1. the question is unclear, incomplete, or poorly worded...
2. the question is mis-categorized - so the correct experts aren't viewing it...
3. the question requires an answer for something that cannot be explained online adequately...
4. specific training, tools, or equipment are required to avoid injury or death...
5. the Experts that are online simply don't have the resources to answer your question fully...

Please feel free to re-work your question if you feel one of these may be the reason.
Of course you are not required - but converting your question to a PAID one usually increases the reply rate as well.

Normal rates for FixYa are...
$ 9.99 answer for one question.
$12.99 Live Real-Time online chat or premium e-mail support.
$29.99 Live Real Time phone support
Sometimes FixYa will run specials for unlimited questions via monthly subscription or reduced rates for limited periods.


Consider the savings that can be had when an informed Expert can save you a $100 service call, or a $350 trip to the car dealership.
Your problem solved - guaranteed! Or your money back!!

If you don't want to pay - feel free to re-submit your question so it returns back to the top of the work queue if you still need help.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question

http://www.applianceaid.com/fault_codes.html

I'd say that as long as you turn off the burners which have the crack and remove the knobs - you're ok, but don't blame me if something happens. Any appliance tech would tell you "No, it's not safe!" just for the liability reasons. Use common sense.

provided the elements are good, the thermostats alternate sending power to the elements so the water heater will not draw too much power and trip the breaker. if you are concerned, replace both thermostats exactly as they are wired and that should fix the problem as long as the elements are good.

1. Check that the bake/broil elements are ok. Do they glow red when cycled on?

2. Control board may have failed. We see this as a common failure. We repair control boards at www.fixyourboard.com

yes alot of times when you use the clean the door will latch then not unlock....these have micro switches that lock and unlock the door.....this is gonna be either one of the switches or the door latch assembly itself.

could be a bad bake element, bad temperature sensor, or control board problem

what does the oven readout display for temperature? if the readout agrees with the actual oven temperature ... it is probably the element

if the oven readout displays a much higher temperature it may be the temperature sensor (the probe in the oven cavity) or the control board

the temperature sensor can be tested by measuring its resistance with power off and unplugged from the control board, should be about 1100 ohms at 75F

If the sensor is good, then it is probably the control board ... in which case we can repair it for you at www.fixyourboard.com

I found the solution on a "solution" section right here! the range may be in the "lock" mode. Press the "clock" and the "bake and hold" buttons together for 3 seconds then release. You may have to repeat this if your display still says "lock".

I THOUGHT THE INFORMATION WAS TOO STEEP I WILL WORK IT OUT MYSELF

The F0 code means loss of safety signal, you must replace the adapter board.

You could try to unplug the unit for a few minutes and then plug it in as a short term fix, but if the code reappears, then replace the adapter board

try reseting the clock as lots of ovens will not work untill clock is set

Try this first, if the temperature is off contact me.
Put an oven thermometer at the center of the oven and set the oven to 350 degrees F.
 
Check the temperature indicated on the thermometer after 20 minutes. If it's not within 5 degrees of 350, you'll need to adjust the oven's temperature control.
 

check the selector swich and thermostat.

on the knobs one of the switches are bad.. you would have to remove the metal panel that is over it. they usually come as a complete harness.. as for the 4th one that is not sparking you have a bad electrode.. (the thing that does the sparking..

you have a bod oven control. but make sure you are getting 240v to oven..

Check that both elements are working, and that there is 240 VAC being supplied to the oven (one of the two breakers has not tripped, or one of the two fuses has not blown.).

Hi, try the hard reset. switch it off and disconnect the power for ~10 mins and then switch on and see.