20 Most Recent Lexmark C532n Color Laser Printer - Page 2 Questions & Answers

The printer will stop printing is there is an error, check for any paper jam before printing. Take note of the error message and locate the exact jam.

Use the manual feeder when printing on envelopes. You may click on the link http://bit.ly/rnHp5b to see instructions on how to go about the procedure using the manual feeder.

For further assistance, please call Lexmark Technical Support.

Please click on the link to see instructions on how to go about the procedure.

http://bit.ly/rpdCUD

For further assistance, please call Lexmark Technical Support.

These defects normally occur when printing is attempted on unsupported media or when the printer is set up for a different type of media than the media that is actually loaded into the machine.

Check your media and ensure that it is suitable for use in the printer. Refer to the printer's user manual for information on supported media types and weights. Is the media you are printing on supported in the printer?

Ensure that the paper type is set accurately on the printer operator panel (go to Menu/Paper Menu/Size-Type/Tray1/Type). Is the paper type set correctly on the printer operator panel?

Change the paper weight setting to heavy on the printer operator panel (go to Menu/Paper Menu/Size-Type/Tray1/Type/Heavy Paper/Check button). Try printing your document again. Did the error return? If the error returns, please contact Lexmark Technical Support for further assistance.

i had the same problem and got on a chat with lexmark technical support and they helped me fix it, they referred me here http://i26.tinypic.com/24bj3tw.jpg, make sure those two crank wheels are in the up position, i did that and immediately the printer recognized the pc units and started working, i still had to reset the counts on the pc units, but the printer was instantly functioning

Not sure what your question is but this link may be helpful:

http://support.lexmark.com/index?segment=SUPPORT&userlocale=EN_CA&locale=en&productCode=LEXMARK_C532&page=product&frompage=null#1

you need to replace fuser on printer

Hi

You need to replace drum of your printer

1. Try unplugging the Printer for 30 seconds, Plug it back in and try it out. if problem persists next step.
2. Uninstall driver, re download it from the Lexmark site here

If no solution please let me know.

Try turning the printer off and leaving it off for a few seconds. If the error does not return on power up, it may have simply been an isolated incident. Continue using the printer, but keep an eye on it for the next week or two. If the error still shows, here is the detail solution: http://www.marketpoint.com/article.cfm?id=119&bhcp=1

was this printer removed or installed while it was powered on? if it was the control board in the lower tray will need to be replaced this can and often does short the board. does the tray show up in the paper menus?

how are you hooking this printer up to begin with? ethernet? when you installed it was it hooked to a usb cable? if it wasnt on usb you should uninstall the previous installation hook it up with a usb cable to install it, this should make it show up in system properties. then madify the install to a network printer from there

Try to replace the fuser. If that doesn't help, system board may need to be replaced. But I strongly suggest you contact Lexmark Technical Support to further investigate the problem. Thanks.

The problem could be caused by the photoconductor units. Try to swap the affected photoconductor units (like swap the magenta with black and cyan with yellow). If problem still occurs, then the photoconductors need replacement. I suggest you contact Lexmark Technical Support for assistance. Thanks

Yes; you can go to lexmark.com and download the drivers.

Unfortunately, there is no User's Guide or manual available online to guide you on how to replace the fuser of your Lexmark C532 printer. For this particular concern, since the fuser is a field replaceable unit (FRU), the Authorized Service Providers (ASP) can better assist you with this. I advise you to call Lexmark technical support at 1-800-LEXMARK (1-800-539-6275). If you need more assistance, leave a comment. I'll get right back to it.

Hi:

From the ready menu scroll down and find the supplies menu. Under the supplies menu you will find the Replace Supplies Menu. Select it. Then scroll dyel to yel PC unit, select it and that will turn off the prompt.

Good Luck

Andrew

. There are rollers that cling on to the paper and move it through the machine. When the rollers are worn down they do not grip the paper. For a short fix you can get something rough like sandpaper, brillo pad, etc, and gently scratch the rollers to give them some traction. This will temporarily solve your problem until you can get the rollers replaced.

yes.it is possible.you will just have to select the legalsize in the printer properties to print on the legal size paper.if not selected the printout will get cut little bit from its end. ok.