Top 20 Lexmark C772dn Laser Printer Questions & Answers

Not a very fast job if you end up having to replace the motor itself. But thats the fuser motor PN = 40X1661. You can pull the fuser out look to the right side and see a white gear find. A lot of time that gear or the ones around it are worn out. Every now and then its just the fuser itself has broken gears or something is stuck in the gear.

click on this link. http://support.lexmark.com/index?productCode=LEXMARK_C522&segment=SUPPORT&pmv=print&page=content&actp=TOP_DOCS&id=SO3607&locale=en&userlocale=EN_US

Go to Lexmark website enter the model number and get driver and/or complete printer install download for free.

You may download the Lexmark drivers and software from http://support.lexmark.com/index?locale=EN&page=product&userlocale=EN_US&productCode=LEXMARK_X5450&focusedTab=PUBLICATIONS#2

You may download the Lexmark drivers and software from http://support.lexmark.com/index?locale=en&page=product&productCode=LEXMARK_X5075&segment=SUPPORT&userlocale=EN_US&frompage=null#1

You may download software and drivers from here.

a usb cord is an extension cord for you to used in case your usb ports is loose, it differs in length according to your neeeds

Please power off the printer. Remove all the toner cartridges. And then put them back in. Make sure you install the toner cartridges properly. After that power on the printer. Try printing again.

kindly download the driver from this linkhttp://en.kioskea.net/download/download-895-driver-lexmark-x5470

Hope this helps. Please rate my response.Thanks.Have a good day.

From the Lemark Service manual

A 100.01 ITU error indicates that the printer did not detect the ITU belt home sensor. Before proceeding with this

service check, make sure that the Second Transfer Roll is correctly installed. After you reinstall the Second

Transfer Roll, check to see if a 100.01 ITU error is still displayed. If a 100.01 ITU error is still being displayed,

continue with this check.

The ITU has an optical sensor that watches for a piece of reflective tape on the inside of the image belt. This

tape is read every revolution of the belt. If a signal is not received from the belt sensor within a certain time

period, the printer posts an error due to the loss of signal. There are several causes for the loss of signal. First,

the belt has tracked too far to the front or rear of the printer. In this case, the belt is still turning, but the reflective

tape is no longer passing within view of the belt sensor. This is considered a belt tracking error and is initially

posted as a 100.02 ITU Error. The other causes of a signal loss could be a belt stall, meaning the belt is not

turning, or a true signal loss, which would be due to a bad sensor, broken cable, loose connection, or bad

system board. These other causes post as a 100.01 ITU Error.

To assist the printer in determining the cause of a signal loss, there is a buffer that records the belt position for

the last 50 revolutions. If the printer loses the belt signal, it refers to the buffer. If the buffer shows significant

mistracking before signal loss, it will post a 100.02 ITU Error. If the buffer shows that the belt has been tracking

in the center before signal loss, it posts a 100.01 ITU Error. Due to memory restrictions, the buffer is not saved

during POR. This means if a printer posts a 100.02 ITU Error, so the belt is tracked off, and the customer or

servicer turns off the printer to clear the error, when the printer starts up, it will still not see the belt signal and will

now post a 100.01 ITU Error because the buffer is empty. When servicing a printer for a 100.01 ITU Error, it is

important to view the error log. See "Display Log" on page 3-29. The error log can only be displayed at this
point. Do not try to print the log. Look for past occurrences of 100.01 ITU Errors preceded by a 100.02 ITU Error.

Fix this Error - use an advanced registry cleaner for Windows that allows you to safely scan, clean, and repair registry problems with a few simple mouse clicks. Problems with the Windows Registry are a common cause of Windows crashes and error messages. By using PC tune-up utilities such as registry cleaners regularly, your system will be more stable, your software will run quicker, and your operating system will boot faster.


http://www.errorfixreviews.org/


or you can try this option Solution#1- If your printer does not show in your hardware list its means that problem belongs to data cable. Kindly check your printer's data cable and plug it properly.
Solution#2- Uninstall printer's software take a reboot and then reinstall its software and then attach your printer or during installation if installation requires.

Good Luck

You may go to support.lexmark.com website to download the printer driver. You may also click the link http://bit.ly/rfMfPm

Please call Lexmark Technical Support for additional assistance.

Please click on the link to see instructions on how to go about the procedure.

http://bitly.com/pguMf7

Please call Lexmark Technical Support for additional assistance.

You can download the Lexmark printer drivers from theirsupport WEB site. Please click on this link and select your model printer todownload :- http://support.lexmark.com/index?page=home&locale=EN&userlocale=EN_US&segment=DOWNLOAD

Pleaseclick on the link to see instructions on how to go about the procedure. http://bitly.com/pguMf7 For further assistance, please call Lexmark Technical Support.

http://downloads.lexmark.com/downloads/pssd/Lexmark_Universal_UD0_Win_32_PCL_XL_Emul.exe

http://downloads.lexmark.com/downloads/pssd/Lexmark_Travel_Print.exe

http://downloads.lexmark.com/downloads/pssd/Lexmark_Phonebook.exe


Those are the software and driver u need the first link is driver and other two are sowftware.

After install please rate solution.

Visit: http://support.lexmark.com/index?locale=en&segment=DOWNLOAD&startover=y&userlocale=EN_UK&question=Lexmark+C772dn+Laser+Printer&productCode=LEXMARK_C772N&page=answers&detectedProductFacet=CMS-CATEGORY_REF.LEXMARK.PRODUCTS.COLORLASER.LEXMARK_C772N&searchid=1287377536340#1


Click on Downloads, get the drivers

I've seen alot of problems with this series with color lines on printouts. pull the cartridge(s) out that are making the colored lines, it's usually the PC drum (The roller on the bottom of the cartridge) has become defective, look for the rust/ bubbles on the roller. Sure sign it's the cartridge(s)

http://support.lexmark.com/index?locale=en&segment=DOWNLOAD&startover=y&userlocale=EN_US+&question=+x2350&productCode=LEXMARK_X2350&page=answers&detectedProductFacet=CMS-CATEGORY_REF.LEXMARK.PRODUCTS.ALLINONE.LEXMARK_X2350&searchid=1285916135470#3