20 Most Recent
Sharp Aquos LC-46D62U 46 in. LCD HDTV - Page 9 Questions & Answers
I have a 42" sharp
http://www.sharpusa.com/CustomerSupport/ProductDownloads.aspx
This is the link to Sharp's manual download page.
Select "model not listed" then enter your model # and enter. Go to page 49 and it gives the diagram of how to pull the stand off and the tools needed.
Hope this helps
Cracked screen repair LCc46d62u
You can't repair cracked LCD screens, they can only be replaced. Unfortunately LCD screens cost more than the TV is worth. If you do happen to find a replacement screen, it's a pretty simple job (just a bunch of screws you have to remember where they go.) You can email me
[email protected] if you need more detailed instructions.
We have a television, no power. what is the
This could be many things.
First.
Unplug the tv from the outlet (wait 60 seconds)
Second:
Plug the tv back in
If you still do not get power and no leds or standby lights you might have a fuse in this tv that has blown out on you. Even worse case is the power board inside could be defective, meaning your going to need to have it repaired.
Please out of consideration of the free answer please do not forget to leave a positive rating or feedback, thanks Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/edwy_1a56970cf1ea4620
How do I connect my Logitech music system to the
If your music system is only audio,then you need two RCA type audio cables pair for left& right audio channels(male pin jacks).Connect them at Music system audio output with left & right channels accordingly while on yr TV,connect the other ends to the audio Input jacks(female type).
If there is a video out also from your music system then add the yellow video cable as well in the same way.
Sharp aquos lines threw the picture
I've seen this problem before and if caught early (usually only a few pixels), its fixable. But if it has already started forming a "line" it might be too late and you might have a defective LCD panel. Most of the time, doing the factory initialization helps with this problem.
(WARNING: THIS GIVES YOU ACCESS TO
THE SERVICE MENU. DO NOT ADJUST ANYTHING IN THE SERVICE MENU OTHER THAN
WHAT I PROVIDE YOU IN THESE INSTRUCTIONS. IF YOU DECIDED TO ADJUST
ANYTHING OTHER THAN WHAT I PROVIDE YOU IN THESE INSTRUCTIONS, I WILL
NOT BE RESPONSIBLE IF ANYTHING WRONG HAPPENS TO YOUR TV.)
- unplug
tv
- press
and hold at the same time “Vol –“ and “input” button on the TV set.
- while
holding those buttons, plug the tv back in
- the tv
should turn on by itself, keep holding the buttons until the letter “K”
appears. Then let go
- then
at the same time press “Vol –“ and “Ch. Down”, you should see the service
menu appear (if it does not appear, try pressing the two buttons again, it
needs to be exactly at the same time)
- Then
use the “Ch. Down” button to navigate down the service menu until you see “Industry
Init” (NOT Industry Init +cause)
- Then
press “Vol +” to toggle it to “ON”
- Then “/////////////////”
should appear.
- when
the screen turns GREEN, unplug the TV. Wait about 30 seconds, then plug
the TV back in.
- Then
continue on with the initial setup again.
TV turns itself off for about 15 seconds then back
This problems is a power glitch happen once in awhile not a problems.Happen all the times,than the Tuner board have problems,must be replaced.That the board where the coalax signal plug into it.Tries Shopjimmy.com,Ebay.com to buy a refurbish Tuner board for the replacement.
Will the TV work in Australia?
No,if this tv was purchase in the US,Mexico or Canada,because it used NTSC signal frequencies.If u buy it belong in European Union it work fine all European Union work on PAL signal frequencies.Ride a Kankaroo for me,never had a chance was there before.
Not finding what you are looking for?