20 Most Recent
HP Photosmart C6180 All-In-One InkJet Printer - Page 9 Questions & Answers
HP PHOTOSMART C7280 ERROR 0xc18a0001
Follow the steps carefully from the front panel of the All-in-One.
1. Get the unit into the “Support Menu” by following the steps given below.
A. - Press and hold the “*” key.
B. - Press the “#” key and release both keys.
Now Display should say “Enter Special Key Combo”
C. - Press and release in sequence the “1”, “2” and “3” buttons.
Now the Display should say “Support” and display the FW rev (something like R0631R)
2. Press and release the right arrow button until the display says “System Configuration Menu”.
3. Press and release the “OK” button.
4. Display should say “Hardware failure status”. If not there already, Arrow Key over to “Hardware failure status”,
5. Press and release the “OK” button.
6. Display should say “Hardware failure status: Clear. Press OK to clear”.
7. Press and release the “OK” Button. Message changes to “Hardware failure status Cleared. Press Cancel to continue”.
8. Press and release the “CANCEL” button as many times as necessary, so that, either the “Welcome to Photosmart Express” screen appears, or, the “Ink System Failure” screen appears. PLEASE DO NOT TRY TO PRINT AT THIS STAGE.
9. Using the Power Button, turn the unit OFF and unplug the power cable from back of the printer and wall outlet.
10. Wait 30 seconds for the power to get discharged and then plug the power cable into the wall outlet first and then into the back of the printer
11.Turn the unit on. The printer may display message “USE POWER BUTTON TO SHUTDOWN THE PRINTER” followed by “PRESS OK TO CONTINUE”. Press OK. The Printer will start the “ONE TIME INK INITIALIZATION PROCESS”. Allow this process to complete and do not interrupt. Once the initialization process is complete, the printer will print out a Diagnostic Page.
12.To verify printer functionality print a SELF TEST PAGE. If SELF TEST prints, then printer is ready for use or Software Installation.
0xc19a0002
1. connect the printer directly to the walloutlet...2. then remove the ink cartridges and then clean the copper contacts with a lint free cloth... then put back the ink cartridges... and check3. then unplug the power chord from the back of the printer without turning off the printer and then press and hold the power button for 30 sec... then plug in the power chord at the back of the printer.. and check if that works...4. if it does not work then unplug the power chord from the back of the printer... press and hold down the pound(#) and 6 key together... then plug in the power chord at the back of the printer... release the # and 6 key when the printer is powering back on... this is a reset which we are doing on the printer...if the printer is on check if the error msg is there or not...if it helps well and good.. however if it does not then try with a different set of ink cartridges... after changing the ink cartridges still it does not work then it might be an issue with the printer hardware...
My pinter's usb connection does not have a
You dont need to have USB or wireless connection to remove cartridge. Turn the printer off and on. Open the front access door. The Carriage ( that holds the cartridges ) will move to center and you can remove it. If you are unable to remove the cartridge when the printer is on, Turn if off, Open the Carriage access door and move the carriage manually and remove it.Regards,Sean
Printer keep restarting. c6180 hp photosmart
Apparently some defective components were used in the construction of the logic board (see photo). On my C6180 there were 3 failed capacitors (the green cylinders - the puffed top indicates failure) and a 4th from the same manufacturer (TEAPO - many unfavorable web references to this manufacturer). I purchased 3x 330uF 16V and 1x 680uF 10v rated to 105 degrees Celsius (total about 60cents). On the logic board, the capacitors I replaced are labeled C613, C614, C660 and C662. If you are not comfortable replacing the parts yourself (or don't have a soldering tool), you will have to find someone who will. The time to repair should be less than 30 min - I did it in 25 min with only a solder pen. This also fixed the ink system failures the printer was having. A similar fix may apply to other printers produced by HP around this time.
Ip address
Find my IP Address
Click start type cmd press enter
you will be in DOS mode
type in ipconfig press enter you will see all of your
internet connection details type in your default gateway ip adress into your
internet search should read something like 10.0.0.138
Your IP Address should be thought more as your computer's
phone number than it's address, if you have multiple connections, you have
multiple IPs if you dont have a connection, you dont have an IP.
Without further delay If you need your computers IP address:
This will work in almost every case, it simply requests the website's server to
tell you what your IP is.
http://whatismyipaddress.com/
I have included a link to make things easier.
If you are in a network and need your computers local
address.
Hold the windows button (looks like the windows banner,
usually between left ctrl and left alt) and press 'R'.
A box will display, and type in "cmd.exe" and hit
enter.
The 'command prompt' will display, a black screen with white
lettering.
Simply type in ipconfig. This gives information on all your
internet connections.
Look for the line "IPv4 Address".
If you need to find the IP of a current connection you can
type (from the command prompt) "netstat".
This will give you all your current connections.
To identify a specific one, the easiest way is
to run it before you establish the connection then again afterwards.How
to Change IP Addresses
Your
IP address is a series of numbers that identify your specific computer on the
Internet.
If, for some reason, you want to
change your IP address, you can do so without going into the command prompt.
Click "Start," "Control
Panel," "Network and Internet" and "Network and Sharing
Center."
Click "Change adapter
settings."
Right-click the network you want to
change and click "Properties."
Click the "Networking"
tab.
Put a check either next to Internet
Protocol Version 6 (TCP/IPv6) or Internet Protocol Version 4 (TCP/IPv4) and
click "Properties."
Click the radio button next to
Obtain an IP Address Automatically if you want Windows to assign one, or click
"Use the following IP address" to manually change it.
Enter the requested information and click
"OK."
My C8180 All-in-one has the
here's what the battery should look like inside your printer.
"0xC18? errors may also mean that the printer's temperature is below 40F/5C.. Try warming up the printer.
My Hp c6180 printer has error masage " Improper shut down"
I had the same problem. Try shutting it down by holding the off button and unplugging it for a few seconds from the back of the printer. Wait a couple of minutes and them plug it back in. Make sure you are connect to a wall outlet and not a power strip or surge protector.
If this doesn't work, hold down the #6 key while cord back from the printer.
Hopefully one of these two would work.
If it doesn't you can go to the HP site and start a chat with a tech who will walk you through a solution.
I had the same problem, and got resolved.
Not finding what you are looking for?