20 Most Recent
Canon PIXMA MP160 All-In-One InkJet Printer - Page 4 Questions & Answers
Canon mp160 fault code E27
Solution that WORKED!!!
NEW REDACTION!!
posted on Feb 09, 2010
pineworks
Rank: Guru
Expert
Rating: 87%, 1202 votes
Hi there
Canon printers MP 160 AND MAYBE
OTHERS
A) E5, E6 or E4 - it is cartridges error
- to fix press the "stop\reset" button for 5-7 sec. and then release
B) E27 - it is code for reset absorber (EEPROM reset or
Waste
ink counter reset) and follow the described below
procedure:
With the printer powered off but connected
to a power source,
1) First..while pressing and holding the Stop/ Reset button,
press the Power button..do not release the Power button
2) Wait till the Power light is ON, then while still pressing the
Power button... press the Stop/Reset button two times (visible for
alert-orange-LED lights on & off).
3) When releasing both the Power button and the Stop / Reset button
(regardless of order), the printer will move into the
service mode. Waiting for menu selection visible for:
- On/off light is fixed green
- Display shows "0"
- A4/Plain paper light is fixed green
4) Being in this Service mode, press the Stop/Reset button the
specified number of time(s) according to the
function listed in the table below.
- Each time the Stop/Reset button is pressed, the 2
LEDs (A4<>Alert) switch alternately into orange and
green, starting with orange.(Note: press 4 times for waste ink counter
reset).
The number of Reset button pressing:
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset
5) Turn off the printer.( it must be turned off)
then turn it on again.
Only in B) case you can enter into "service mode", in A) case if
have e.g. paper jam, or another error you CAN'T
enter
the "service mode"
Try it
THANKS..JUST GREAT!!!
E3 Error
MP160 PIXMA paper feed jam E3 error. I completely solved this on my Canon MP160 printer but it is a common problem and the fix may work for others such as MP130 MP140 MP145 MP150 MP170 or MP180. With the problem I had, the printer would make the usual motor whirring noises but would not feed the paper. The usual c-clunk sound that indicated the feed roller has been engaged was not there. The screen warning said to remove jammed paper and the printer showed an E3 error.
The problem was caused by the ink cartridge carrier becoming stcky on its track and not fully returning to the rest position on the right side (as viewed from the front). The fix involved taking the printer apart and lubricating the cartridge carrier track and the ramps that lift the cradle that rises to cover the printheads. Unfortunately you have to dismantle the printer and separate the scanner unit to get to the lubrication points. Its not a quick fix.
When you have the printer apart you will see a prominent white lever held by a coiled spring just behind the rest position of the ink cartridge carrier. The lever is actuated by the ink cartridge carrier when it moves to the right. If the lever is not actuated, the motor drive will never engage the large grey feed roller and the paper in the hopper cannot be fed into the printer. Make sure to also put some lube onto the lever at the point where it is struck by the ink cartridge carrier.
Canon MP160 Paper jam error E3
MP160 PIXMA paper feed jam E3 error. I completely solved this on my Canon MP160 printer but it is a common problem and the fix may work for others such as MP130 MP140 MP145 MP150 MP170 or MP180. With the problem I had, the printer would make the usual motor whirring noises but would not feed the paper. The usual c-clunk sound that indicated the feed roller has been engaged was not there. The screen warning said to remove jammed paper and the printer showed an E3 error.
The problem was caused by the ink cartridge carrier becoming stcky on its track and not fully returning to the rest position on the right side (as viewed from the front). The fix involved taking the printer apart and lubricating the cartridge carrier track and the ramps that lift the cradle that rises to cover the printheads. Unfortunately you have to dismantle the printer and separate the scanner unit to get to the lubrication points. Its not a quick fix.
When you have the printer apart you will see a prominent white lever held by a coiled spring just behind the rest position of the ink cartridge carrier. The lever is actuated by the ink cartridge carrier when it moves to the right. If the lever is not actuated, the motor drive will never engage the large grey feed roller and the paper in the hopper cannot be fed into the printer. Make sure to also put some lube onto the lever at the point where it is struck by the ink cartridge carrier.
Mp160 user please help
Here is the fastest way for both of you, if you have a little money but you get it back. Go buy another one run it, get what you want and return the printer, get your money back and start printing. I can't do what you posted because I'm lazy.
Error E 4, 2 canon pixma mp 160
E42 means scanner error. May require a hard reset(disconnect from power supply for 30 min). Otherwise may require factory reset procedure to be applied. Follow the steps below:
Mp160 Reset Counter
Service mode operation procedures -
1) With the printer powered off but connected to a power source,
press the Power button while pressing and holding the Stop/ Reset button.
2) When the Power LED is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order),
the printer will move into a service mode. (Waiting for menu selection)
4) When the LED lights in green, press the Stop/Reset button the specified number of time(s)
according to the function listed in the table below.
(Each time the Stop/Reset button is pressed,
the LED lights alternately in orange and green, starting with orange.)
The number of the Reset button pressing LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset See waste ink counter reset procedures below.
5 times Orange Destination setting See Destination setting procedures below.
6 times Green Print head deep cleaning
11 times Orange Button / LCD checking
12 or more times Returns to a menu selection
Canon printer E2
printer in side paper or not feedind paper or paper sensor damaged
How to reset ink cartridge for mp 160
First, download the software at http://www.box.net/shared/4yblbn34kg
Secondly, to run the software your printer has to be in service mode. Do that by
- unplug cable
- press and hold "power" button
- plug cable
- press "resume" and release
- release the "power" button
At this stage, your computer will detect a new hardware
Run the software.
Canon MP120
just open the front door while the printer is on. the carriage will move and stand to the cartridge install position.hold the colour cartridge pust it little bit towards down till it leaves the lock and then get it ouside towards ur side.fit the new cartridge in the reverse procedure.
thanks.
E22 error code
E 22 is a carriage error, which means there is still something wrong in the cartridge area.
Please do as follows:
Turn off the printer and unplug it.
Remove the cartridges. Check them for leaking or damage.
Look carefully inside the cartridge slots. Look for dried ink or blobs of ink (they can be cleaned away with a tiny bit of alcohol on a qtip. Look for bent or broken cartridge wire holders? Does everything look okay?
Leave the cartridges out. Plug the printer back in and turn it on.
Does the carriage move?
Reinstall the cartridges and make sure they are properly seated.
Close the lid. Turn off the printer
Restart your computer.
Turn the printer back on.
Tell me what is happening now. unless everything is okay!
Not finding what you are looking for?