Top 20 Brother DCP-330C All-In-One InkJet Printer - Page 6 Questions & Answers

Open the front of the printer by pulling the front panel toward you and down. (where you replace the toner cartridge)Remove the toner cartridge/drum unit assembly by pulling up and toward you.separate the drum unit from the toner cartridge by pressing the green release tab on the side and lifting them apart.place the toner cartridge into the new drum unitreplace back in the printerpress "clear/back" button and then press "1" to cancel "replace drum" messageclose the front panel.http://support.brother.com/g/b/faqend.aspx?c=au&lang=en&prod=mfc7340_us_as&faqid=faq00000154_039

Check the ventilation fan on the side. Might not be working. Remove any foreign material blocking the fan.

re install soft ware

'unable to print 73' is a Printhead error.. Usually the printhead is an expensive part around $80 to $110, and you will need a full set of cartridges to prime the new printhead.. Sorry to say that this repair is not normally economical to go ahead with.

maintenance unit is not working normally. See if any thing is stuck or replace it.

Error code EF - Irregular power supply is detected Print Unable EF Turn the power off and then back on again.

This is a common occurrence for these machines. They can get confused when cartridges are changed before they read as empty. To correct this. 1) Unplug the printer from both the Power and Computer and remove all cartridges closing the cartridge access panel. 2) Plug the printer into the Power only and turn on. The machine will complain about no cartridges, this is fine. 3) Open Ink access panel and insert the first cartridge (Black is most common and close the panel. 4) The machine will complain about the missing cartridges. Open the panel and insert the second cartridge in the sequence and close the panel again. 5) Repeat the process for the third and fourth cartridge. 6) Once all cartridges have been installed the printer will ask if you have replaced the cartridges. Say no to the Black, Cyan and Yellow but yes to the Magenta and it will display the correct readings. If this process fails to read the cartridge still then there is something wrong with the sensor inside the machine which probably means new machine.

Replace the high voltage PCB or the main board.

This machine uses a Reset Gear to instruct the printer it has a new cartridge. The Starter Cartridge that comes with the machine does not have this gear attached to it so refilling the cartridge without installing and resetting the gear will not allow you to print normally. If you are using a store bought cartridge that you have since refilled you can reset the gear to tell the printer it is a new cartridge.

You can get third party software in order to avail the facility to combine pdf to a single file

A picture of the printout is required to confirm, nevertheless, it could be toner. Printing does not use scanner, so it has nothing to do with the scanner.

Go to the Brother Website for your region. Find the Downloads section. Put in the details of your machine and search for the appropriate downloads for your machine. Download the Drivers, Manual etc from there. Some of the regions may even offer to sell you a CD with all the downloads on it. But just download what you need.

windows make loads of hardware errors, if it is not being picked up by the computer but the printer is turning on check it has not been installed as with the same name but a number after, if so select that for printing if not try plugging the usb lead from the printer in to a different socket on the PC. hope that helps ma

Pull out the paper tray. Lift the cover of the tray. Slide paper into the tray. Close the cover of the tray. Push the tray back into the machine till it clicks into place.

I am a Brother employee working for the software technical support department. We have drivers available for the DCP-J132W posted on our solution site. http://support.brother.com/g/b/producttop.aspx?c=eu_ot&lang=en&prod=dcpj132w_eu Brother Software Technical Support http://www.brother-usa.com DCP J132W Others Brother Solutions Center

The printer or the drum/toner unit may cause the grinding or clicking noise.

1. Power off the printer and open the front cover.
2. Remove the drum/toner unit and close the front cover.
3. Power the printer back on.

If the grinding or clicking noise dose not occur when the drum/toner unit is removed from the printer, then the drum/toner unit is the cause of the noise. Install a brand new drum unit and/or toner cartridge may be necessary to stop the noise. Still having Problem Then follow Us For Brother Printer Support

Ghosting on machines can be one of several causes.

1. Poor Quality/ Damp toner - Replace the toner cartridge
2. Worn Drum Unit - Replace the Drum Unit
3. Fuser Unit Failing - Replace the Fuser Unit (Normally more than the printer is worth).
4. Damp Paper - Open a new ream of paper and try printing again (This is the cheapest option to start with diagnosis).

check da scanning unit

Refill or replace toner.

Magenta Print-head may be blocked. Depending on the model of machine. Either on the Menu on the printer find Ink Management or press the Ink Management button. Print a Test Page If no Magenta Dots showing then proceed to Cleaning and Clean the print-heads through the proceedures given on the machine. Print another test page. If Magenta Dots are fine then cleaning done. if not then try cleaning again. If still not fine then the machine will need to be cleaned professionally which will cost a reasonable amount. Most service fees are more that it is to replace the printer.