Top 20 Brother DCP-330C All-In-One InkJet Printer Questions & Answers

Brother DCP-330C paper jam

Very good article for what this error is and how to fix it here: brother error code 46

replace the maintenance unit .

you have a blocked or faulty printhead/ inksystem, you can print an internal print quality check and do deep head cleans, but in my experience this only helps 10-20% of the time. deep head cleans use A LOT of ink if you dont see a big improvment after 2 deep head cleans dont continue as you are just wasting ink

This error is associated with the self test the printer does on the print head during power-up of the printer. Sadly, it is indicative of either a faulty print head or a faulty main control board, neither of which are easy or inexpensive to replace. Unless you can get hold of another machine with a different fault and swap over the print head and/or board (you'll need very good skills and tools to do this) then I'm afraid the machine is beyond economic repair*. * Brother will repair your machine but the cost will likley be more than a new one.

This error is associated with the self test the printer does on the print head during power-up of the printer. Sadly, it is indicative of either a faulty print head or a faulty main control board, neither of which are easy or inexpensive to replace. Unless you can get hold of another machine with a different fault and swap over the print head and/or board (you'll need very good skills and tools to do this) then I'm afraid the machine is beyond economic repair*. * Brother will repair your machine but the cost will likley be more than a new one.

Machine Error 46 indicates that the ink absorber pad is full and needs replacing. You will need an engineer to replace this. If your machine is out of warranty, please contact Brother Customer Service: 7777 North Brother Blvd. Bartlett, Tennessee 38133 1-877-BROTHER (877-276-8437) 901-379-1215 (fax) M-F, 9:00am to 8:00pm Eastern Time

Menu. Black Start(Mono Start), Menu and Black Start(Mono Start) "Maintenance 10" will display on the LCD

laat het oude gewoon staan, en voeg een nieuwe toe..geeft geen problemen

that does not go everything is blokt

check error code (46?)

usually you will find language choice in set up menu display.

Replace the waste ink tank and reset purge counter

samsung 4300 tonner reset problem

click here for manual

press "menu" "black start" and "up arrow 4 times".
that gets you into maint. mode to be able to reset purge counter.
next enter code "80" by pressing up/down arrows and pressing "ok".
press "black start" several times until you see "purge count".
now press "2783" and "ok" to reset purge count.
then press "black start" about three more times or until you see flushing count. again, press "2783" and "ok" to reset. now hit "stop/clear" a couple of times and press "99" to exit or use arrows to get to "99" . at this point, you may have to press "ok" to get out of maint. mode, but i think once you press 99 it backs out automatically. next time this comes up however, you will need to have your ink absorber box and flushing box replaced.

Click here Click on above link select os and download driver and install. Let me know if you need further assistance. Thanks for using FixYa.

I'm afraid there is no simple solution to this problem.
Error codes 50 and 51 refer to problems with the purging mechanism - some of the whirring and clicking noises you hear when the machine self cleans or starts up are it purging ink from the print head. Through some very clever mechanics, the machine uses the paper feed motor (running in the opposite direction to normal) to perform purging.
Possible causes listed in the Brother Service Manual for this error code range from "simple" things like a misaligned cam, to complex problems with the main control board. However, whatever it is, dismantling these machines isn't staright forward and parts are very diffciult to obtain and very, very expensive, so much so that 99 times out of a 100, it isn't cost effective to repair.
You could approach a Brother service agent, but it's highly probably that they will charge you more than buying an equivalent brand new machine.
Sorry.

Sure. Go to the manufacturers website at:
http://welcome.solutions.brother.com/bsc/public/us/us/en/dlf/download_top.html?reg=us&c=us&lang=en&prod=dcp330c_all
and this will allow you to download the printer driver.