Top 20 HP PL5060N 50 in. Plasma HDTV Questions & Answers

hi it sounds like your plasma has gone in stand by mode look on youtube will tell you all about stand by type in how to fix and tv make model stuck in stand by more than likely capacitors blown if your not any good soldering boards id phone tv guy out but if you are then youtube it hope this hopes

Do a reset to this TV, and then check. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here. Pull up older posts. https://electronicshelponline.blogspot.com/ Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.

Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis. http://electro-medical.blogspot.com/ To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main board.

Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/ To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement.

Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/ In some models of LCD TVS; the backlight inverter and its T'Con board will be a part of the panel itself, and will be a built-in type inside the LCD panel. If so, they can't be replaced. In this case; a panel replacement is the only repair. For some other models, the backlight inverter section circuit will be a part of the main power supply regulator [SMPS]. To such sets, the power supply section circuit too should trouble shoot. Contact any service technician. The circuit will differ with models and versions. Type in the brand name of your device, in the search box [at the top right] of the display window and the Search will start at once as you type in, and will show you all the related posts. It will make surf easy.

That's a pretty broad question. Is it the cable, is it the female end on the back of the tv? If it's on the tv side of things then you'll need to open up the tv and check connections to the HDMI port. If all is good, replacing just the port is an option. It should have a part # on it if you want to be certain it has the same connection to your tv. I suspect they're almost all the same, I've only seen a few from a couple tv brands.

The TV needs professional service or replacement.

sell it

There should be any short circuit to any of the circuit boards inside it. Check and locate the board first. Being a plasma display, the circuit will be quiet complicated to an experienced person to work on. If you wish to get some details, check the site linked here. Pull up older posts.

you probably messed with the contrast settings. try restoring them to default.

eo6 on screen

Y-Sustain should be suspected. Make sure before replace it. If you wish to get more details, check the site linked below. Pull up older posts there. Check the site with patience, as it has over 2400 posts now. All are related to electronic equipment repair help. If you search the site in Timeslide option, which can be selected from the drop down list at the top left of the display window, it will be easy to locate the related post. You can also do a search by type in the brand name to your device into its search box at the top right of display window.http://electronicshelponline.blogspot.com/

NO you have an over heating problem, I see a bunch of Boards and Proccesors, But NO fan in this TV CHIPS get hot they need more then a heat sink that just spreads the damage

I have a seven year Plasma TV HP PL5060. When I turn on the TV, I have sound but no picture, the screen display (power on) is a snowy blue screen and vertical pink stripe. What is causing this problem and how can I fix it cheap. I can afford a TV repair man at this time, because I am laid off from work. Thanks.

If the set has a input or source button on the outside or side it can be got at and removed (not the plastic button but the switch under it) they do fail in this way and with it removed and the issue gone you can use the remote instead.

I had this problem for weeks before giving up. I just had another go and i resolved this by downloading my gpu driver but not installing, then i un-installed my mobo hd sound driver and my gpu hd sound driver. Then i installed the latest nvidia driver from my hard drive. When the driver activated i got some buzzing for 10 secs and then presto (hd sound) via HDMI. However my pc tells me still "no audio capable display". computers are often wrong.

are you looking for a power supply board for this model?.

Visit the site named 'Electro-help' for more details. Check this link and select the site named above. View it in 'Flip card' option, which can be selected from the drop down box menu by the [Sidebar] tag, at the left top left corner of the display window. It will make search easy. Some times, the ads attached with each posts both at the right and bottom, might help you to find the availability of spare parts. There are more than 640 posts to different brand TVs now. Will be updated daily.

I would say it is power supply related. Consult a Technician.

Just replace the y sustain board