Hello Hendrix, I pass the list of reasons why your Panasonic SA-MAX5000 tells you F61, this information is taken from The Community
ELECTRONICOS.com
F61 The DC DECT circuit of the "micro" detected an anomaly. * See: Note 1 Source:
www.comunidadelectronicos.com
* Note 1: The error code F61 is one of the most frequent and its origin can be due to different causes. This occurs when the "micro" (IC system control) detects a variation in the reference voltage of the pin called DCDET. This voltage is 5 V. Through this pin (in some models are two: DCDET1 and DCDET2), the micro monitor the presence of DC voltage (direct current) in the speaker output, in addition to the voltages (+ and - ) power supply of the output stage and the other voltages provided by the source (5, 9, 15V, etc.) A short circuit or excessive consumption at any stage of the equipment, resulting in the absence or fall below the normal value, of any of the voltages of the source will cause the reference voltage of the DCDET pin to drop below 5V, causing the micro to turn off the equipment and present the F61 code on the display. The same happens if there is a direct voltage (DC) in any of the outputs to the loudspeakers, of the power stage. In most of the cases that the error code F61 is presented, it is usually due to problems in the power stage. For this reason, it is advisable, as a first step, to check this stage, completely disconnecting the integrated output circuit and testing the equipment again. If you turn on normally, without presenting the error code, it is necessary to replace the integrated one. If after disconnecting the power integrated, still continues to present the code F61, it is necessary to start the checks on the pin or DCDET pins of the "micro" and trace the cause from there. The same could be due to some defective component in the same DCDET circuit, or, because any of the supply voltages is absent or below normal. Not detailed here, specific data on identification of components or voltages of the circuits, because these vary depending on the model. But in all cases the reference voltage in DCDET is 5V The DCDET pins of the "Micro", vary according to the model, for example: in models SA-AK15, SA-AK18, SC-AK27 (and others) pin 32 in models SC-AK22 / 33/44/55 (and others) pins 33 and 34 If it is determined that error F61 is due to any of the voltages absent or below normal, obviously the cause in the corresponding circuits. In summary: A fault in the output stage or any of the power circuits, including voltage regulators, diodes, capacitors, etc., may cause the F61 error code to appear. A "locked" mechanism can cause the consumption of a motor to be excessive, reducing the corresponding voltage due to the overload and also producing the indicated code. As indicated above, the causes can be diverse, but starting the search, from the pin or DCDET pins of the micro with the help of the diagram, you can locate the source of the problem, in order to solve it.
Source:
www.comunidadelectronicos.com
I hope it will help you find the solution
Greetings Franco Dosil
Hola Hendrix, te paso el listado de motivos por el cual tu Panasonic SA-MAX5000 te indica F61, esta informacion la tome de La Comunidad
ELECTRONICOS.com
F61 El circuito DC DECT del "micro" a detectado una anomal?a. * Ver: Nota 1 Fuente:
www.comunidadelectronicos.com
* Nota 1: El c?digo de error F61, es uno de los que suele presentarse con mayor frecuencia y su origen puede deberse a diferentes causas. Esto ocurre, cuando el "micro" (IC system control) detecta una variaci?n en el voltaje de referencia del pin denominado DCDET. Dicho voltaje es de 5 V. A trav?s de ese pin (en algunos modelos son dos: DCDET1 y DCDET2), el micro monitorea la presencia de tensi?n DC (corriente continua) en la salida de altavoces, adem?s de los voltajes (+ y -) de alimentaci?n de la etapa de salida y los dem?s voltajes proporcionados por la fuente (5, 9, 15V, etc.) Un cortocircuito o consumo excesivo en cualquier etapa del equipo, que produzca la ausencia o ca?da por debajo del valor normal, de alguno de los voltajes de la fuente, har? que el voltaje de referencia del pin DCDET baje por debajo de los 5V, haciendo que el micro apague el equipo y presente el c?digo F61 en el display. Lo mismo ocurre si existe tensi?n continua (DC) en alguna de las salidas a los altavoces, de la etapa de potencia. En la mayor?a de los casos que se presenta el c?digo de error F61, suele deberse a problemas en la etapa de potencia. Por ello, es recomendable, como primer paso comprobar esta etapa, desconectando totalmente el circuito integrado de salida y probando nuevamente el equipo. Si enciende normalmente, sin presentar el c?digo de error, es necesario reemplazar el integrado. Si despu?s de desconectar el integrado de potencia, aun continua presentando el c?digo F61, es necesario comenzar las comprobaciones en el pin o pines DCDET del "micro" y rastrear desde all? la causa. La misma podr?a deberse a alg?n componente defectuoso en el mismo circuito DCDET, o, a que alguno de los voltajes de alimentaci?n est? ausente o por debajo de lo normal. No se detallan aqu?, datos concretos sobre identificaci?n de componentes o voltajes de los circuitos, debido a que estos var?an dependiendo del modelo. Pero en todos los casos el voltaje de referencia en DCDET es 5V Los pines DCDET del "Micro", var?an seg?n el modelo, por ejemplo: en los modelos SA-AK15, SA-AK18, SC-AK27 (y otros) pin 32 en los modelos SC-AK22 / 33 / 44 / 55 (y otros) los pines 33 y 34 Si se determina que el error F61 se debe a alguno de los voltajes ausente o por debajo de lo normal, obviamente habr? que rastrear la causa en los circuitos correspondientes. Resumiendo: Una falla en la etapa de salida o cualquiera de los circuitos de alimentaci?n, incluyendo reguladores de voltaje, diodos, condensadores, etc., puede ocasionar que aparezca el c?digo de error F61. Un mecanismo "trancado" puede originar que el consumo de un motor sea excesivo, reduciendo el voltaje correspondiente debido a la sobrecarga y produciendo tambi?n el c?digo indicado. Como se indico anteriormente, las causas pueden ser diversas, pero comenzando la b?squeda, desde el pin o pines DCDET del micro con la ayuda del diagrama, se puede localizar el origen del problema, para as? solucionarlo.
Fuente:
www.comunidadelectronicos.com
Espero te sirva para encontrar la solucion
Saludos Franco Dosil
https://www.comunidadelectronicos.com/
https://data2.manualslib.com/pdf6/126/12518/1251783-panasonic/samax5000pn.pdf?0b037fce2e01f8dd9f10def6145c9438&take=binary