20 Most Recent Philips 37PF7320A 37 in. HD-Ready LCD Television - Page 7 Questions & Answers

This should be an error code 14. Most of the Philips TVs with this code means the Audio is the problem.
The Audio board maybe shorted out causing the TV to go into "Protection Mode". I would try unplugging the Audio board from the main power supply board and main mother board to see if the TV powers up without going into Protection Mode. That should give an answer if the Audio board is bad or not.

Hi gt
To answer your question;
We`re getting to see this problem more and more often on philips tv`s, and it usually has to do with software upgrade.
With your tv`s model number you can go on philips website and download the upgrade at the address below:
http://www.support.philips.com/support/catalog/downloads_catalog.jsp;jsessionid=8888F7981C720E8018961175739D41D6.app106-drp2?groupId=SOUND_AND_VISION_GR_US_CARE&userCountry=us&categoryid=TV_CA_US_CARE&navAction=push&pageFrom=downloads&navCount=1&userLanguage=en
You will need a usb flash drive/memory stick to do this procedure and there is a file on how to do it.
If you have problems with it , let me have your model# and i`ll help you.
Hope this help good luck

This is an easy fix using the Philips remote control that came with your tv. On the center of the remote is a dial that has left right up down controls. Stand in front of the tv and using those controls you can recenter the screen and get rid fo the green line. I had same problem when we hooked up hd satellite reciver to philips 37 plasma

I had the same problem when we hooked up an hd satellite box. It's a simple solution using the Philips remote that came with your tv. The dial in the center of the remote with up down left right control will move the picture left or right up or down by holding the direction you want to go. Make sure to stand in front of tv.

reset default settings.

water problem in house after burst pipe-tv on but red/blue light
flasting continuously. sky box has red/orange light as normal.
what is problem

Power board is dead,replaced the power board will get power back.

Hi,

Kindly Provide few more Details :-

1. Model of the TV?
2. How Old the Unit is ?
3. How many blinks you could see like 6 blinks then pause then 6 blinks?
4. Are you willing to Repair it or you would like to have a Repair estimate?
5. Do you have the tools to Fix this?

Let me know, so that we could proceed.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

looks to me that your main board fail.

One of the boards (module) has a short on it, and or the power supply itself is failing.
The service center will find the fault using the process if elimination. They will replace the bad boards or modules as required to get the set working again.

Jerry G.

Hello. I believe I can assist you. On your TV remote there is a button called input. Push that button. Then you will see a menu of each of the possible sources of signals for your tv. Go down through them until your Wii appears on the screen. ALSO remember that you will have to change the input selection again when you want to watch television.
Regards, Joe
PS please rate my answer. Thank you.

We have cable from ETEX and yesterday out of the blue my sound went completely off! I don't know what caused it and it is not muted. How do I get sound back?

I have the exact same problem! I have it hooked up to a power strip now to unplug it by flicking of the power strip and waiting for the red light to go out then I turn it back on while Channeling up 10 X's and then down and up until it comes on. I listen to the sound of the switch which it comes on. I turn it off if it is faint and then back on and channel up. Crazy process but it's been working. It takes about 10 minutes everytime to get the TV on until I get a tech to come out and look at it. The capacitor keeps a charge which is why the light is flashing with a code for 60 seconds./JJ

unit is in the service mode you need to bring it to ashop with a service remote to clear it

Hi my name is Roety,
I can help you with your issue ,
6 Blinks is a bad Y buffer Board error code.
You can check for bad capacitors , but most likey will need the Y sus main, Y upper and Y lower buffers replaced .
Tech labot is about $250 plus parts about $600　
　
　
If I have helped you with your issue please click accept.
If you have more questions you can still respond until this post expires,
I will reply asap
Thanks I’m happy to help further over the phone at https://www.6ya.com/expert/eric_ab7c09ec01841771

Sounds like you got a bad capacitor in the TV most would be in the power supply region. Not much I can tell from the error code your getting as its a General hardware fault code. If you have General working knowledge of TV's you "could" pop this thing open and examine Swollen Capacitors, Fuses, Foil leads etc etc.

If this is under any type of warranty bring it into the shop and get your work done Free if its not you might be digging in the pocketbook for repairers here.

Thanks for using fixya.com please do click the accept button. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620

that is a common problem you will need your mainboard replaced about 250 for the board
the problem is the cpu ic lost a ground inside it

proberbly not thats youre line output transformer gone it will cost you about 75 pounds to replace and repair

Me too? Any solutions yet?

There are two places to look for the problems, the backlight inverter board and the power supply. Look at the power supply first since it is easier to get to, look for burnt parts, bad capacitors, etc.
http://en.wikipedia.org/wiki/Capacitor_plague
Please post back what you find.