20 Most Recent KitchenAid 24 in. KUDS02FR Built-in Dishwasher - Page 3 Questions & Answers

Some dishwashers have a soft food disposal inside. If something is hung up, it will grind or hum for a long time. If this is the problem, it will eventually go away.

This could be the relay that controls the heating element, I dont see a separate relay so it may be on the main board. The relay could be stuck closed due to the high current that might have welded the contacts closed. It could also be a sensor issue that is closing that relay. The error code you listed says it is detecting cold water.

Press High Temp Scrub and Dry Heat option buttons in quick succession one after the other for about 6 sec until all the lights come on. Then press Cancel button. This should reset the dishwasher. Press equivalent buttons on the panel if the actual ones above are not there. Make sure the dishwasher detergent dispenser lid is shut and the dishwasher door is shut before you start the above reset sequence.

Sound like the is a problem with one of the supply pipes for the water check they are not blocked and the is no turn off on

There are several touch pad buttons that could activate the Child Lock feature on a Kitchenaid dishwasher. To toggle off the lock, try pressing and holding the 4-hour delay dry or the energy saver dry key pads for 4+ seconds. The Energy Saver Dry is used for the Child Lock on the Kitchenaid KUDS25SHWH1. This manual is here: https://c.searspartsdirect.com/mmh/lis_pdf/OWNM/L9050329.pdf . The 4-hour delay or Control Lock options are listed in this manual: https://www.kitchenaid.com/content/dam/global/documents/201605/owners-manual-W10596243-RevD.pdf . If neither of these steps work, you may have a problem with the keypad, the wiring between the keypad and the control board or the control board itself. Please add a comment with the model of the dishwasher if you'd like me to try and find the parts list/diagram. If the machine is under warranty, you may want to contact Kitchenaid. I hope this helps. Cindy Wells

I experienced the same problem after my tension cables broke. The door fell open with such force that it bent the hinges a little. If you've replaced the tension strings (which you should do every 5-8 years) then you don't have to replace the latch. I did and it didn't solve the problem.Here's the solution:Put a towel at the bottom of each side of the door by the hinge.Push the door closed a couple of times to bend back the hinges.Remove the towels and you're back in action.Good luck

Sounds like control board failure

Manual next link https://www.manualslib.com/manual/87795/Kitchenaid-Kuds01fl.html?page=13#manual some links below dealing with water leaks. My thought, If the water starts pouring out after a while it could have to do with the dish washer drain pump, hoses and connections. https://www.youtube.com/watch?v=bwrlocTT2sM https://www.youtube.com/watch?v=zDNiLvApKLc https://www.youtube.com/watch?v=7b1-M_WKYJs https://www.youtube.com/watch?v=ZwIcooyu7GI https://www.youtube.com/watch?v=uUQQuVitEdo https://www.youtube.com/watch?v=F-ddBOqEb0E https://www.youtube.com/watch?v=DQWIOBvC2XU https://www.youtube.com/watch?v=edsv5aJCEEA https://www.youtube.com/watch?v=uvJhZt1FIr8

The blinking usually happens when your house power goes off and then comes back on. Press the Start/Cancel Button to reset.

My recommendation is the heat exchanger has failed or default, this can happen anytime but typically after 5+ years old

If you replaced the door latch did you replace the striker? Those are the only 2things that keep it closed.

Call the company that made it and ask them what could be wrong.

For the Kitchenaid KRFF507ESS01, to clear the power outage indicator (blinking "PO"), press the Measured Fill button on the key pad. That is the right-most button below the screen. The manual for this refrigerator is available at Sears Parts Direct on the product page: https://www.searspartsdirect.com/partsdirect/user-manuals/krff507ess01-kitchenaid-parts-manual . The current link to the manual is https://c.searspartsdirect.com/mmh/pd_download/lis_pdf/OWNM/1507129L.pdf . See page 21 of the manual for information on the power outage indicator. Look in the right hand column. The manual is also available from Kitchenaid on the product page: https://www.kitchenaid.com/major-appliances/refrigeration/freestanding-refrigerators/freestanding-french-door/p.26.8-cu.-ft.-36-inch-width-standard-depth-french-door-refrigerator-with-exterior-ice-and-water.krff507ess.html . Scroll down (or use the link) to the Manuals & Guides section. Expand the section by clicking on the +. The direct link to the manual is https://www.kitchenaid.com/content/dam/global/documents/201504/owners-manual-W10772325-RevA.pdf . I hope this helps. Cindy Wells

This dishwasher have learning control board check your screen filter bottom middle inside make sure it's clean you need to run unit try self diagnostic mode just consentrate on first error message need to found out what is it fix problem and reset control by running diagnostics mode u should found service paperwork on inside of kuckplate (bottom penal holds by two plastic clips or 1/4 " screws

Sorry we do not sell parts of any kind or do we have any locator service to find them for you

Read on some of this information or maybe u still have your use& care guide

It sounds like your dishwasher isnt level or mounted. Make sure also that the rails supporting the top rack are not just jammed. If its sliding like normal and appears to be on track and your dishwasher is mounted, give the top rack a couple slighlty more powerful jerks and tugs to try and unsieze them if they are bound up. Then spray small amounts of cooking oil on the rail mechanism if this breaks it free. If the rails are broke, look them up at repairclinic.com and replace parts.

Make sure there isn't a restriction in the machine-such as clogged filter, hoses etc.