20 Most Recent
Bosch Nexxt Premium WFMC6400UC Front Load Washer - Page 5 Questions & Answers
My washer is alarming "suds or blocked pump"? What can I do?
Plug off the power cord from the wall mains. I give you several alternatives, sort out thru the easiest: Note your brand and model. Check on YouTube for change of motor brushes. Then disconnect your motor and check your brushes; follow noting how you dis-assemble so you can re-assemble easier. If your brushes are less than half an inch long get new brushes (thru this very site Fixya) and refit; actually this is quite easy. The spin has a lot to do with worn motor brushes. Manufactures want you to dump machines and buy; it helps them all. Not you - you shell out bucks.If you have already cleaned out your filter, which is usually just under the tub (be prepared for a lot of water; and disconnect from the wall power socket), your washer still may not spin. So look into next para below. The tech sheet is usually taped to the body of the washer inside somewhere.Note your brand and model. Check on YouTube for change of motor brushes. Then disconnect your motor and check your brushes; follow noting how you dis-assemble so you can re-assemble easier. If your brushes are less than half an inch long get new brushes (thru this very site Fixya) and refit; actually this is quite easy. Thespin has a lot to do with worn motor brushes. Check the motor housing for an overload button, usually on the back and coloured black or red. Give it a push and if it clicks then the motor might have just been overloaded and shut itself off.There is a big connector located at the motor - giving power to the motor (located under the tub) to the right side, could be loose. Disconnect the connector and refit to make sure it is tight. Before refitting the back, etc, try the spin alone; if it works you are done. Click if helped pl, at my solution. I am doing this for the enviro. (& you)
Loud humming noise when spinning
It is so common that the washing machine can make
terrible noise in many ways and is a common fault. In all occasions it is
important that your observation is most important and so is vital to the
identification /rectification and solution. If you have noticed that machine is
vibrating when it is running then the motor /drum suspension has to be
inspected. Since these fittings are located on the underside of the machine it
is important that you look for the noise with a good inspection lamp. Manually
turn the motor and drum and listen for the noise, if so the motor bearings, the
drum agitator shaft and fittings must be checked. Also the suspensions which
include the shock absorbers and springs, the body clamps must be checked to be
in correct alignment and not changed in position. Tightening of the
mounting is also very important. Finally
in most cases a drop of OIL or smear of grease on the moving parts cane solve
most issues.
Check this link :
http://www.espares.co.uk/advice/washing-machines/a/7/1210/wobbly-washing-machine-or-tumble-dryer.html
For
replacement of bearings check for tips on this visual link: http://www.espares.co.uk/advice/washing-machines/a/7/1401/how-to-replace-the-bearings-on-a-washing-mach.html
Fault displays check door
Possible that the lock or the door switch is not aligned or is out of contact. You can remove and check the assembly. Click on
Door
Cold water intake valve is dripping
Possible that the valve is faulty, or that the bandage or hose connection is not tight . You can remove and use some tape to reset the connection, if the water drips further from the valve then it can be due to faulty inlet valve. If so replace the valve.
Soap dispenser overflowing with water
You will have to pull the dispenser tray out and clear any debris. I've seen a sock in one (who knows how that got there,) toys and even a glob of laundry detergent pods leavings.
Bosch washing machine, WAS24460UC, error codes
Hi,
Unplug the Washer for Few Minutes, say 30 Minutes, and then Turn it ON. If the Error Message would not Reset, Read the Information Given by Bosch for this Error :-
However, for a washing machine Bosch list E34 as a door lock fault.
The following is from the service manual.
door lock is broken SAFETY ERROR - switch ON/OFF for reset Normal mode
- door hook is stuck - washing program is aborted - check door lock
- door is stuck - door is unlocked, if possible - check mechanic
- stiff gasket - operator control actions are blocked - check wire harness
It appears you have a problem with the door lock assembly.
Have a look at it, if it's not locking when the door is shut, I'd suggest replacing the door lock on a "fit and see what happens" basis. It's not overly expensive and would be worth trying first. Check all the items mentioned above and let me know how you get on.
Let me know,if needed further assistance.
Hope i helped you.
Thanks for using ' Fixya ' and have a nice day!!
Not finding what you are looking for?