20 Most Recent AT&T EP5962 Phone - Page 7 Questions & Answers

Go to AT& T web site for manual download.

AT E5908 User Manual

Sounds like your phone has a short. If you see the message "line in use" call your number, is it busy, now unplug your phone and call your number again, is it ringing? Indicates a short, possibly in your equipment. As for message " no line" is the electric connected to the phone and did you check for dial tone in tat particular jack with a known, working phone first...just to make sure there's dt @ the jack. Good Luck :)

Ebay is usually a good place to start, Good Luck :)

The model number for your cordless phone is on a small sticker underneath the battery inside the handset. Entering this number at www.manualslib.com will allow you to get a free copy of the original owners' manual. Good luck!

1. To de-register the orphaned handsets from their old base: When the orphaned handset says "Connecting..." enter *331734 [menu] and it will soon beep and display "Not registered" 2. To register the new handset to your base: press the "Handset Locator" button on the base and hold it until the "in use" light comes on ( ~ 4 seconds ), then release the button and set the new handset into the base phone cradle. After ~ 30 seconds it will beep and display "Handset #" (next in sequence). 3: Note: the base handles a maximum of 12 handsets. If your system was fully populated ( ie, a handset is already # 12 ) you will have to clear all the handsets from the base and re-register them all in sequence. ( it is the only way to 'rescue' the places occupied by the lost handsets ). To clear the base of all registrations: 1. Press and hold the the "Handset Locator" button until the "in use" light lights and then starts to blink ( ~ 10 seconds ), release the button -- then press it again briefly while the "in use" light is still blinking. 2. The base will beep and all handsets that were registered will display "Not Registered" 3. Follow the instructions above for each handset in turn to re-register them: press "Handset Locator" ~ 4sec ( in-use light on ), set handset into the base cradle, etc. The manual is available from: www.manualslib.com but does not fully describe these procedures. Good luck !

Try www.manualslib.com or http://www.manualslib.com/manual/762415/AtAndt-E5911.html Good luck!

1. To de-register the orphaned handsets from their old base: When the orphaned handset says "Connecting..." enter *331734 [menu] and it will soon beep and display "Not registered" 2. To register the new handset to your base: press the "Handset Locator" button on the base and hold it until the "in use" light comes on ( ~ 4 seconds ), then release the button and set the new handset into the base phone cradle. After ~ 30 seconds it will beep and display "Handset #" (next in sequence). 3: Note: the base handles a maximum of 12 handsets. If your system was fully populated ( ie, a handset is already # 12 ) you will have to clear all the handsets from the base and re-register them all in sequence. ( it is the only way to 'rescue' the places occupied by the lost handsets ). To clear the base of all registrations: 1. Press and hold the the "Handset Locator" button until the "in use" light lights and then starts to blink ( ~ 10 seconds ), release the button -- then press it again briefly while the "in use" light is still blinking. 2. The base will beep and all handsets that were registered will display "Not Registered" 3. Follow the instructions above for each handset in turn to re-register them: press "Handset Locator" ~ 4sec ( in-use light on ), set handset into the base cradle, etc. The manual is available from: www.manualslib.com but does not fully describe these procedures. Good luck !

Hi, this is a major control fault and you may be able to reset the main board by removing the cell battery for 5 minutes. if the issue still exists after the reset, you will need to replace the main circuit board in this unit.

According to the manual starting on page 52, you need to de-register all handsets then re-register the handsets one at a time. The manual covers both cordless model numbers so the handsets should be interchangeable. I have included a link where you can download the manual if you need it.

http://att.vtp-media.com/ecp/documents/product_Product/127/UserManual/1082/cl82209_manual_i3.pdf

That phone is no longer made, however this part became a head ache for them and they had spares for a while, http://telephones.att.com/

All machines have controls for deleting messages. Read your ****** manual. if no manual go to manufacturer web site.

For a better explanation you should look up your user's manual, if warning is documented. My WILD Guess is that warning appears when you need recharge your batteriy or maybe when battery's voltage/amperage rating is getting too low and probably you need to replace it.

The phone gets it power from the network line or ISDN
if its not getting power from the telephone line it does what you describe

try the phone on a line that proven to work and let me know

thanks

rene