Top 20 Motorola Mobility H3 Bluetooth Headset, Black Headset - Page 8 Questions & Answers

Measuring across the commutator opposites is a rough check - if each pair has the same resistance it is probably good but even then there are no guarantees. I have never seen the armature resistance stated for any motor though that doesn't mean such figures don't exist. It would seem logical that each pair should be isolated but that generally is not how the armature is wired and each commutator segment is the termination of two coils. In reality there is only three ways to test an armature - either build it into a motor and see if it performs ok, use an automated motor fault analysis machine or one of the dedicated armature testers such as an armature growler.

The short answer is no -- the difference between AM and FM is too great though some CB radios were made dual mode, like the President Veep I used to own. Some CBs that found the way into Britain were powerful sidebanders that offered similar capabilities to unlicensed CB-ers to that official radio hams had to sit exams to enjoy. Some radio hams found it cheaper to have those top-line CBs modified for use on the 11 metre amateur band. It would be no help to you to obtain a standard FM CB as when the UK was forced to legalise CB radio under the Treaty of Rome, they legalised it at a different frequency as the American frequency was already allocated to radio control, bleepers and other things. Special CB sets were manufactured for the UK market.

Hello there! Assuming your talking about "XtremeMan SOMA BT" I'm not a fan of assumptions but... if this is the device your are referring to then here you go below. If this is not the device you are making reference to, then please respond with the model number and make/brand of the device. Thanks for your visit and good luck. 1. With the unit on or off, plug the included cable from the USB jack on your computer to the micro USB jack v on this unit. While charging, the battery level will be shown by the LED indicators with the current level LED blinking. When all the LED indicators light solid, then the unit is fully charged. 2. If the power level is less than 10%, the left-most LED indicator will start blinking, which means that the Soma BT needs to be charged. Using the Soma BT with a Bluetooth Device 1. Turn on the unit as shown above. 2. Press and hold the Bluetooth button U for approximately three seconds until a beep sounds and the right-most LED starts blinking. 3. Within five minutes, select Soma BT from the Bluetooth List on the external device. See external device's owner's manual for details. When paired successfully, the Soma BT will beep twice and the right-most LED will light https://www.manualslib.com/manual/1540329/Xtrememac-Soma-Bt.html?page=8#manual Check Here

internal battery is dead no fix known but to replace it

IF you are still having issues with this let me know in a post, there is a reset procedure for these

https://forums.radioreference.com/threads/pro-106-scanner-help-scanner-stuck-on-one-channel.245676/ https://smallbusiness.chron.com/can-scanner-seems-stuck-61253.html

I am guessing the CB has a fault and needs taking to a CB Doctor...

If you're referring to the 200bt portable speaker set, this isnt possible. Car stereos are only designed for input over bluetooth not output. Now if it really important to you, you can use a line level adapter to tap into the rear speakers of your vehicle, take that output and plug it into your speakers with an aux cord, or if you have an after market radio you can use RCA cables and a jack adapter to do the same. If you must bluetooth (eg. out of vehicle operation of speakers) buy a cheap bluetooth output adapter (shark makes one) use a small cigarette lighter inverter to power it, and then you can plug your aux jack into it and bluetooth to a speaker set outside of the car. If you use this in conjunction with the speakers car there will be a delay between those speakers and your bluetooth speakers.

try putting in your make an model then search google for (your item+mk+model+pinout?) like this. *shruggs* mite get lucky

Unfortunately these mics are not professional quality and they tend to be less accurate. The variable selectors have a wide tolerance and are not precise, thus; they tend to be hard to control. Not much you can do...so use it as is, or get a new unit.

You might be lucky but I would doubt it, to me its another Chinese funny, things made for certain companies or supplied to companies who are the sole or limited suppliers. I noticed on the rear of the instruction manual it only gave a short labour warranty and had its company location, most of these type purchases require return to the place that sold it or they will give a service agent to send it to. I have found that with these items parts and manuals are not around so if you are going to fix it yourself you would have to wing it, as they can be made with a variety of parts not the same set as time passes. Hope this helps in some way.........

Connect the headset to the charger as if you were charging it, but keep one side in your ear. Once connected to the charger, hold down the power button. It'll beep a few times and then stop. Disconnect from the charger. You can then turn the headset back on. This "procedure" clears the headset's memory,

cut bluetooth on phone.. unplug alexa and tell her to turn of blue tooth on devices.

I do not know about these items but if it works on other phones then a few things spring to mind, that moto might use a different version of plug like a "3 ring + tip" plus there maybe one with 4 + tip. Another thought is the mic needs power if its an electret type which that moto does not supply. The connection of those earbuds may be wired a little different to how moto needs, many manufacturers do this so you buy their bits and bobs. Lastly the moto may need some feature selection in its menu system to be turned on so look through its settings for audio-microphone etc. Hope this might help

The fashion for nostalgia radio with a modern sound has brought about a clutch of models from only a few manufacturers. I have only encountered one such that was basically an in-house cabinet with bought in internals, the quality of which was probably reflected in the price and as this was from the lower price bracket the internals were from different sources and badly matched. I know of no reason to assume other models would be substantially different because although popular they haven't sold in the high numbers that would justify purpose built internals and so the chances are an experienced audio engineer would probably recognise the circuit board as being from a popular hi-fi and be able to provide you with details.

The user manual should be available on the Radio Shack / Tandy website.

Make sure that the pair on your output device states paired for phone and music. It can still pair for phone and data but not pair to stream music. This is common on android devices especially. If this be the case, unpair the device and forget (delete) the earbuds on your output device. Ensure any bluetooth devices like amazon Alexa, TVs and other common things are powered down. Turn the bluetooth on the output device off, then back on. Search for earbuds and follow manufacturer procedures to sync earbuds. Once found, pair. Ensure when a successful pair happens that they are paired for phone and music. It will tell you on the output device if the pair was successful for both. At this point make sure your volume settings are not muted or all the way down and you should be enjoying music if you have an app playing music.

it is a branded or local one

Scala ic5 download software?

(If you don't have it installed, download Java here.) ... This lets you run single-file Scala programs in your browser using Scala.js, including graphical/interactive ...

First, make sure you have the Java 8 JDK installed.

To check, open the terminal and type: java -version(Make sure you have version 1.8.) (If you don't have it installed, download Java here.) 2

Then, install Scala:

...either by installing an IDE such as IntelliJ, or sbt, Scala's build tool. or Best if you prefer a full-featured IDE (recommended for beginners) DOWNLOAD INTELLIJ ·Getting Started with Scala in IntelliJ ·Building a Scala Project with IntelliJ and sbt ·Testing Scala in IntelliJ with ScalaTest Best if you are familiar with the command line DOWNLOAD SBT ·Getting Started with Scala and sbt on the Command Line ·Testing Scala with sbt and ScalaTest on the Command Line Compared to other programming languages, installing Scala is a bit unusual. Scala is unusual because it is usually installed for each of your Scala projects rather than being installed system-wide. Both of the above options manage (via sbt) a specific Scala version per Scala project you create. But it's also possible to "install" Scala in numerous other ways; e.g., grab Scala binaries and use Scala from the command line or use Scala in your browser!

You likely tripped a fuse or circuit breaker. If you are referring to an automotive type stereo there will be 2 fuses associated with this problem. One is directly on the back of the head unit and is usually 10amp, the other is in your vehicle fuse box usually labeled radio in the diagram.