Sony VPL ES7 SVGA 800 x 600 LCD projector - 2000 ANSI lumens - Page 5 - Answered Questions & Fixed issues

right click on photo and print.
Open it in your default image viewer ( double click the photo) and press print

Please go to menu and check auto power on if it is on make it off

lamp/cover problem in sony es 4 is in two parts, in first case, the led keeps blinking.in this case problem is related with cover switches and thier connection with main board. in second case, led glows permanently, in this case either lamp or ballast pack may be faulty.

put the tv color in vivid mode.

Please give me the model number of the printer.

reset the settings to factory default. is it cut off evenly, or is it uneven and shadowed? if it is the latter and you have a dlp projector, you have a collapsed light tunnel. if it is cut off evenly, go into the settings and make sure the resolution and screen size matches.

The bulb replacement message is not triggered by bulb condition. It comes on after a given number of hours use. If you did not re-set the hours counter to zero when you replaced the lamp then you will get this message prematurely. Don't replace the lamp until it ceases to work correctly - colour balance wrong it it simply does not light.

just go to www.sonystyle.com and download a new driver

You can download Lexmark printer drivers from their support/download WEB site - click on this link to their WEB site :-
http://support.lexmark.com/index?page=home&locale=EN&userlocale=EN_AU&segment=DOWNLOAD

I change the lamp 4 my tv sony vega XL-2400 and I steel send me a signal to change the lamp what can I do 4 setup.

on the floor? find a way of holding it lens side down. on the wall to the floor? back it up and tilt it down.

Solved the replacement problem. Access panel is the entire lower front of the set. Two coin slot fastners, located on the rear down low on the outboard edges are the releases. Having undone those fastners, pull gentley from the outboard edges of the lower front panel. There are big snap fastners that will release as you pull from the bottom, working your way toward the center. Once removed, the cover for the light box is just left of center, held on by two allen or phillips head screws. Remove the screws and pullon the vertical fin on the cover. When it is removed, you can pull on the bulb box, the box will come unplugged and slides out. At this point replace the old box with the new one, and repeat the process in reverse. If you did not buy the box, just the bulb, the internet directions and video are very good. Hope this helps!!

Lamp code XL-2400 is Sony part number F93087500 and it is available on http://www.partstore.com/. You may also decide to purchase the less expensive Philips Lighting lamp part number F93087500RL. Either will work for your television set.

Hi,
After replacing lamp, connect projector AC power cord and turn the projector in standby mode.

Press following keys on control panel for less then 5 seconds each..
RESET, <==, ==>, ENTER.
That will reset lamp timer in projector.
Thanks.

Just go to your Server or Desktop PC and enable the RPC service (Remote Procedure Call)
Right click in "My computer" icon, from the manu select "Manage" then go to "Services and Applications" and expand that, after that select "Services" you will find that services in the right pane, just click in "Start"

Hi!

Here is the manual in PDF, on page 33 you can see how to reset the lamp hours.
http://www.roscorrentals.com/equipment_manuals/Sony%20VPL-PX31.pdf

Good luck!
Nic
DONT forget to RATE me

This is the exact same issue as I described for an Epson user. So I'll repeat it here.

I assume this is an LCD. I don't remember the s4 being a DLP projector.

This sounds like the LCD panel used for the green color has gone out. The image is made up of red, green and blue images layered upon the screen. If the green panel has gone out then there is nothing filtering out the green light in the image. This causes a nice green hue to the whole screen.

It could be a simple open and reconnect fix. I personally have never opened a projector, so I'm not going to walk you through it as I do not know how hard it would be to tinker with. It should eb a cheap fix for a true repair man though.

Most companies have on their web site the soft ware you are looking for. It will ask for the printer model and it will alow you do download it.

The issue has to do with something called "Keystone". This allows you to set the projector at an angle and project on an angle. When you set the projector on a flat surface, you would need to adjust the keystone to get rid of the "trapazoid" look of the image.

Sent to V3 SYSTEMS & SERVICES PTE LTD 64522679,
they are Projector Service Center in Singapore,