20 Most Recent Sony VPL ES7 SVGA 800 x 600 LCD projector - 2000 ANSI lumens - Page 11 Questions & Answers

right click on photo and print.
Open it in your default image viewer ( double click the photo) and press print

Please go to menu and check auto power on if it is on make it off

lamp/cover problem in sony es 4 is in two parts, in first case, the led keeps blinking.in this case problem is related with cover switches and thier connection with main board. in second case, led glows permanently, in this case either lamp or ballast pack may be faulty.

put the tv color in vivid mode.

Please give me the model number of the printer.

reset the settings to factory default. is it cut off evenly, or is it uneven and shadowed? if it is the latter and you have a dlp projector, you have a collapsed light tunnel. if it is cut off evenly, go into the settings and make sure the resolution and screen size matches.

This means you have set the normal display resolution TOO HIGH.

Reduce it to lets say 1024 x 768 to start and then slowly increase it from there until you get the error message again.

Once you get the message drop it back to the last one nd you should be fine.

Bob

ExMod

It would be very decent of you to consider the quality of our experts answers and judge them accordingly as you pass through FixYa.

Thank you

just go to www.sonystyle.com and download a new driver

You can download Lexmark printer drivers from their support/download WEB site - click on this link to their WEB site :-
http://support.lexmark.com/index?page=home&locale=EN&userlocale=EN_AU&segment=DOWNLOAD

I change the lamp 4 my tv sony vega XL-2400 and I steel send me a signal to change the lamp what can I do 4 setup.

on the floor? find a way of holding it lens side down. on the wall to the floor? back it up and tilt it down.

Could you give me the Make and Model # of the remote. Comcast uses several different types.

hello. I can assist you. Check to see what other printing you may have qued up. to do this click on the printer icon in the lower right hand corner and open it up. If there is old printing waiting there either print it or delete it.

if there is nothing awaiting printing you will have to go back through the drill of being sure that the printer and the computer are connected by a wire and then use the disk that came with the printer to reload what is called the printer driver. If you do not have that disk you can download the driver for free. just google the name and model of your printer with the word driver added at the end.

Solved the replacement problem. Access panel is the entire lower front of the set. Two coin slot fastners, located on the rear down low on the outboard edges are the releases. Having undone those fastners, pull gentley from the outboard edges of the lower front panel. There are big snap fastners that will release as you pull from the bottom, working your way toward the center. Once removed, the cover for the light box is just left of center, held on by two allen or phillips head screws. Remove the screws and pullon the vertical fin on the cover. When it is removed, you can pull on the bulb box, the box will come unplugged and slides out. At this point replace the old box with the new one, and repeat the process in reverse. If you did not buy the box, just the bulb, the internet directions and video are very good. Hope this helps!!

Lamp code XL-2400 is Sony part number F93087500 and it is available on http://www.partstore.com/. You may also decide to purchase the less expensive Philips Lighting lamp part number F93087500RL. Either will work for your television set.

Hi,
You can replace lamp by yourself, its an easy job and mentioned in Instruction Manual.
Click Sony Support to download instruction manual copy, please check page-76 for lamp replacement procedure details.
I would recommend to buy Sony Original Lamp for TV safety and avoid aftermarket/ cheap lamp.
Click Sony Accessories Store to buy Sony original lamp for your KDF-42E2000 TV as per following part number..

F93087500 Lamp Block Assy XL-2400 and price is $200

Thanks.

Hi,
After replacing lamp, connect projector AC power cord and turn the projector in standby mode.

Press following keys on control panel for less then 5 seconds each..
RESET, <==, ==>, ENTER.
That will reset lamp timer in projector.
Thanks.